Panasonic 885170283862 Посібник користувача - Сторінка 13
Переглянути онлайн або завантажити pdf Посібник користувача для Стереосистема Panasonic 885170283862. Panasonic 885170283862 32 сторінки.
Друкувати сторінку
█
Main unit displays
"--:--"
•
You connected the AC power supply cord for the first time
or there was a power failure recently. Set the clock.
"ADJUST CLOCK"
•
The clock is not set. Adjust the clock.
"ADJUST TIMER"
•
The play timer is not set. Adjust the play timer.
"AUTO OFF"
•
The system has not been used for 20 minutes and will
switch off within a minute. To cancel, press any button.
"DIMMER"
•
You have set the volume to "0". After 10 seconds, the
system switches on the dimmer function.
"ERROR"
•
An incorrect operation was done. Read the instructions and
try again.
"F61"
"F77"
•
Disconnect the AC power supply cord and consult your
dealer.
"F703"
•
Examine the Bluetooth
®
device.
•
Disconnect the Bluetooth
and then switch on again.
"F76"
•
There is a problem with the power supply.
•
Disconnect the AC power supply cord and consult your
dealer.
"NODEVICE"
•
The USB device is not connected. Examine the connection.
"NO DISC"
•
You have not put in a disc.
"NO PLAY"
•
Examine the content. You can only play supported format.
•
The system may have a problem. Switch off the system and
then switch on again.
"PLAYERROR"
•
You played an unsupported MP3 file. The system will skip
that track and play the next one.
"REMOTE 1"
"REMOTE 2"
•
The remote control and the main unit are using different
codes. Change the code of the remote control.
–
When "REMOTE 1" is shown, press and hold [OK] and
[ ] for a minimum of 4 seconds.
–
When "REMOTE 2" is shown, press and hold [OK] and
[USB/CD] for a minimum of 4 seconds.
"SOUND 1 NOT SET"
"SOUND 2 NOT SET"
"SOUND 3 NOT SET"
•
You have not saved the sound effects into the sound
setting number.
"USB OVER CURRENT ERROR"
•
The USB device is using too much power. Disconnect the
USB device, switch off the system and then switch on
again.
"VBR"
•
The system cannot show the remaining play time for
variable bit rate (VBR) tracks.
device. Switch off the system
®
Remote control code
When other Panasonic equipment responds to the
remote control of this system, change the remote control
code for this system.
Preparation
Press [USB/CD] to select "CD".
█
To set the code to "REMOTE 2"
1
Press and hold [CD] on the main unit and
[USB/CD] on the remote control.
"REMOTE 2" is shown.
2
Press and hold [OK] and [USB/CD] for a minimum
of 4 seconds.
█
To set the code to "REMOTE 1"
1
Press and hold [CD] on the main unit and [ ] on
the remote control.
"REMOTE 1" is shown.
2
Press and hold [OK] and [ ] for a minimum of
4 seconds.
System memory reset
Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
1
Disconnect the AC power supply cord.
2
While you press and hold [1] on the main unit,
connect the AC power supply cord again.
Continue to press and hold the button until
"– – – – – – – – –" is shown.
3
Release [1].
All the settings are set back to the factory preset.
It is necessary to set the memory items again.
Maintenance
To clean this system, wipe with a soft, dry cloth.
• Never use alcohol, paint thinner or benzine to clean this
system.
• Before using chemically treated cloth, read the
instructions that came with the cloth carefully.
13