Panasonic RX-VT80 Інструкція з експлуатації Посібник з експлуатації - Сторінка 12

Переглянути онлайн або завантажити pdf Інструкція з експлуатації Посібник з експлуатації для Стереосистема Panasonic RX-VT80. Panasonic RX-VT80 14 сторінок. Portable stereo component system

Друкувати сторінку

Recording

EDIT/FM MODE/BP

HIGH/

STEREO/II

NORMAL/

STEREO/II

MIC/

MONO/I

Use normal position/TYPE I tape only.

Preparation:

Wind the cassette just past its leader so that recording can begin

immediately.

Press [

STOP/EJECT] and insert the cassette to

be recorded in DECK1.

Insert the tape with the side to be recorded facing out (

Close the tape deck by hand.

Set [SELECTOR] to the source to be recorded.

Radio recording:

Tune in the station. (

CD recording:

Insert the CD you want to record (

Prepare the desired CD recording mode.

Remote control only

• To record programmed tracks

(

Program play on page 8)

VCD 1.1

: do steps 1, 3-4

MP3

• To record CD/tracks by using CD Play Modes

(

CD Play Modes on page 8)

VCD 1.1

Make sure that the CD is stopped.

1-REPEAT mode: do steps 1,3-4

MP3

VCD 1.1

[

NEXT] to select the track.

Tape-to-tape recording:

Insert the tape inside DECK 2 with the side to be played

facing out. Close the tape deck by hand. (

Set [EDIT/FM MODE/BP] to HIGH or NORMAL.

HIGH: High speed

NORMAL: Normal speed

RQT7801

PBC /

OSD

MUL

MULTI SCREEN

TI SCREEN

DISPLA

DISPLAY

TIME ACCESS

TIME

ACCESS

ZOOM

PLA

PLAY MODE

MODE

A-B REP

PROGRAM

SELECT

PBC / CLEAR

PBC /

CLEAR

ENTER

ALBUM

SHIFT

RESUME

V-INDEX

-INDEX

page 11)

page 6).

: do steps 1-2

: do step 1

MP3

1-REPEAT mode: Press [

page 11).

Radio and CD recording:

SELECT

PLAY

PLA

Press [

[

PLAY] is also depressed with [

CLEAR

STOP

Note for CD recording:

Press [

the unit display.

SELECTOR

Recording and CD play automatically begin simultaneously.

RADIO

Tape-to-tape recording:

TAPE/

Press DECK1 [

Press DECK2 [

Deck2 playback and Deck1 recording start simultaneously.

Recording stops and the buttons are released when the end of the

tape is reached. (DECK1)

To stop recording

Press [

To pause recording

Press DECK 1 [

To resume recording, press DECK 1 [

If the tape finishes before the CD

The CD continues playing. Press [

To record on the other side of the cassette

Turn the cassette over and press [

Note

• Do not change the editing selector during editing. The playback

sound may flutter.

• Any changes made to the volume or sound quality during recording

will not affect the recording.

Erasure prevention

Break the tab.

Cover

the

adhesive tape when you

want to use the tape for

recording again.

Recording tips

• Changes to volume and tone will not affect the recording.

• Wind the cassette just past its leader so that recording can begin

immediately.

• When recording MW, set [EDIT/FM MODE/BP] to the position

where there is least noise.

• Use the AC power supply cord or insert fresh batteries.

• When erasing recorded sound,

Insert the tape in DECK 1.

Set [SELECTOR] to TAPE/

Set [EDIT/FM MODE/BP] to HIGH or NORMAL .

Press [

Your attention is drawn to the fact recording pre-recorded tapes or

discs or other published or broadcast material may infringe

PREV] or

Recording through the built-in microphone (MIC)

Set [SELECTOR] to TAPE/

Set [EDIT/FM MODE/BP] to MIC/MONO.

Insert the tape in DECK 1 with the side to be recorded facing out.

Close the tape deck by hand.

Press [

Face towards the sound source.

Note

• When recording through the built-in microphone, no sound will be

heard from the speakers.

REC] to start recording.

REC].

REC] after the track numbers and so on are shown on

PAUSE], then press [

PLAY] to start recording.

STOP/EJECT].

PAUSE].

PAUSE] again.

PBC/CLEAR, STOP] to stop it.

REC].

Side A

tab

with

Tab for side B

OPR OFF

REC].

OPR OFF

REC].

Tab for side A