Alpha Communications TekTone NC377 Посібник з монтажу та експлуатації - Сторінка 4

Переглянути онлайн або завантажити pdf Посібник з монтажу та експлуатації для Адаптер Alpha Communications TekTone NC377. Alpha Communications TekTone NC377 12 сторінок. Paging interface adapter

Друкувати сторінку

Chapter 4—Programming

Default User Name & Password

The NC377 is shipped with the following default user name

and password:

User Name:

comppage

Password:

pia3264

TekTone

suggests you keep these defaults. (See Changing

the NC377's User Name & Password in the Appendix to

change the user name and password.)

Logging On, Loading Programming Screen

1. For the PC to communicate with the NC377 Paging Interface

Adapter, they must both be on the 192.168.1.____ IP subnet.

TekTone

suggests using 192.168.1.235. Temporarily change

the IP address of your PC or laptop. (See Changing a PC's

IP Subnet in the Appendix for instructions.)

2. Connect the PC/laptop to the NC377 using the gray cross-

over cable.

3. Apply power to the NC377 Paging Interface Adapter and

turn it on; the green power light will light. The NC377 will be

operational approximately 40 seconds after power up.

4. Open a browser, such as Internet Explorer, on the PC/ laptop.

5. Locate the NC377 Paging Interface Adapter's IP address on

the label attached to its main circuit board.

In the browser's address line, type the IP address, followed

by /default.zhtml in lower case letters. (For example,

192.168.1.239/default.zhtml)

6. The Welcome screen will appear (see Figure 5). Click on

Configuration Settings.

7. The Logon screen will appear (see Figure 6). Enter the

default user name and password:

User Name:

comppage

Password:

pia3264

8. Click OK.

9. The Global Settings screen will appear (see Figure 7).

Page 4 • IL871 NC377 Paging Interface Adapter Manual

Global Settings Programming

Referring to the Figure 7, while logged on to the interface,

configure the following:

Date and Time—(Master NC377 only.) The NC377 has an RTC

(real time clock). Set the clock to the current time so all logs

and reports will reflect the correct date and time.

• Type the date in mm/dd/yyyy format, including slash

marks (09/01/2009).

• The NC377 uses a 24-hour clock. Enter all digits, includ-

ing colons, in hh:mm:ss format (12:15:00).

IP Address—(Do not change.) The address of this NC377.

Host System—Select TekTone as the Host Nurse Call System

you will connect to this unit. The program will automatically

set the correct sample rate for the Slow and Fast pulse rate.

Unit ID—Select the type of unit to be programmed. Each unit

must be identified as a Master, or as Slave1–Slave8.

• Master

• Slave 0 (no slaves), or

• Slave1–Slave8

Number of Slaves—(Master NC377 only.) Select the number

of slaves (0–8) that will be attached to the master.

Master/Slave Port Setup—(Do not change unless you are

directed to by TekTone

controls the data speed on the RS485 bus. It is factory set.

Protocol—(Master NC377 only.) Select Scope when using the

TekTone

NC369 Paging Transmitter.

Data Type—(Master NC377 only.) Select Alphanumeric.

Baud Rate—(Master NC377 only.) Select 512.

Device to Transmitter Port Setup—(Master NC377 only.) This

setting must match the port settings of the paging encoder

installed. Select 9600-N-8-1 for the TekTone

Transmitter.

Total Number of Contacts—Select the number of inputs that

are installed in the NC377 being programmed (32 or 64).

Monitoring Pagers—(Master NC377 only.) All alarm notifica-

tions will be sent to the Monitoring Pagers (in addition to the

Pager IDs assigned to specific alarms in contact input

programming).Enter Pager ID and Alert type (A, B or C).

Use this formula to convert the pager's CAP code to its

corresponding Pager ID (add leading zeros to make 7 digits):

Pager ID = [(pager's CAP code × 8) + 10000].

System OK Check—(Master NC377 only.) Select a pager ID

and time interval for the system to transmit a System OK

check-in message. Enter Pager ID, Alert Type and Time

Interval. (After the screen has refreshed, the Pager ID's

leading zeros will not display; this is normal.)

Technical Support.) This setting

NC369 Paging