Epever RTU 2G A Посібник

Переглянути онлайн або завантажити pdf Посібник для Сенсорні термінали Epever RTU 2G A. Epever RTU 2G A 2 сторінки. Gprs transmission terminal

Друкувати сторінку

HUIZHOU EPEVER TECHNOLOGY CO., LTD

※ Thanks for selecting the EPEVER RTU 2G A solar wireless collector.

Please read this manual carefully before using the product.

※ Please keep this manual for future reference.

GPRS Transmission Terminal

1. Important Safety Instructions

Read the instructions and warnings in the manual carefully before



installation.

The product should be situated away from the rain, exposure, dust,



vibration, corrosion, and intense electromagnetic environment.

Please avoid water and other liquids enter into the product.



Never use the product at sites where electrostatic could occur, and avoid



the antenna close to a metal object.

DO NOT disassemble or attempt to repair the product.



Power supply: DC 9~60V or 5V, it can be customized according to



customers' requirements.

Enable GPRS service for the SIM card before installation.



2. Overview

EPEVER RTU 2G A is a new wireless data transmission terminal based on

the GPRS network. With the GSM/GPRS SIM card, the connected devices

can easily access the EPEVER cloud server to realize remote, wireless, and

networked communication. EPEVER RTU 2G A is suitable for EPEVER solar

controller, inverter, and inverter/charger.

Features:

Extensive network coverage and flexible networking



Low operating costs (charged by network flow)



Adopt a non-standard DB9 male terminal



Embedded in Modbus RTU protocol



Automatic restore after disconnection



Support RS485 communication



3. Appearance

❶ Antenna port

❷ Hole

★The pin definition of the terminal(DB9 female) connected to the DB9

male terminal❸ is as follows.

Item

1/2

Indicators

You can observe the indicators' color and status through the hole❷.

Name

Color

Network indicator

Red

(LED2)

Slowly flashing (5s)

EPEVER RTU 2G A

❹ Fixing screws

❸ DB9 male connector★

Terminal

Definition

Floating

VCC2

Power2 (12V/200mA)

GND2

Power GND2

GND1

Power GND1

Floating

RS485-A

RS485-B

VCC1

Power1 (5V/400mA)

Status

Instruction

Correct power supply

On solid

Unregistered GPRS network

Registered GPRS network

successfully

TEL: +86-10-82894896/82894112/+86-752-3889706

Sync. Indicator

Green

(LED1)

Power indicator

Green

(LED2)

4. Parameter Configuration

Step1: Connect the DB9 terminal ❸ to the PC through a DB9 to USB adapter.

Note: Connect an external power adapter to the DB9 female terminal to supply the

EPEVER RTU 2G A.

Step2: Insert the SIM card and power on the EPEVER RTU 2G A. For detailed

SIM card installation, refer to chapter 6, Installation.

Step3: Open the configuration tool on the PC and click the "connect" button

to connect the EPEVER RTU 2G A successfully.

Step4: Click the "Read" and "Write" buttons to configure the parameter.

Step5: After configuring, power on the product again to make the modified

parameters take effect.

Common configuration parameters:

Parameters

Configuration

Server Info

No modifications are recommended

Different countries have different APN, and please make sure APN

APN

firstly. Products will not be connected to the Internet with fault APN.

China APN: CMNET

APN User

Enter it according to the actual

APN Key

Enter it according to the actual

Baud

Set it according to the connected controller or inverter

5. System Connection

EPEVER RTU 2G A can be applied to the following solar street light systems.

Through a GPRS signal, users can easily monitor the operating status and

modify the related parameters on the Cloud platform.

Note: The EPEVER RTU 2G A supports 5~18V DC power. While a larger transient

current is needed when the wireless network sends the data, it is suggested to

adopt a power adapter of DC 5V/500mA or above.

6. Installation

Step1: Install the SIM Card

① Purchase a SIM card and activate the GPRS service.

② Undo the three screws from the EPEVER RTU 2G A.

③ Push the shell upward and take out the circuit board.

④ Take out the small SIM card and insert it into the card slot correctly.

⑤ After installing successfully, reinstall the product shell.

Step2: Install the silicone pad

Tear off the silicone pad's adhesive and stick the silicone pad to the DB9

terminal of the EPEVER RTU 2G A.

Step3: Install the antenna

Connect the 4G antenna to the antenna port of the EPEVER RTU 2G A.

Website: www.epever.com

Registered GPRS network

Slowly flashing (5s)

successfully

Turn off after a

Correct power supply

flashing