DieHard 200.71225 Посібник користувача - Сторінка 5
Переглянути онлайн або завантажити pdf Посібник користувача для Зарядний пристрій DieHard 200.71225. DieHard 200.71225 17 сторінок. Microprocessor controlled, fully automatic operation battery charger with engine starter plus battery and alternator tester for 6 and 12-volt batteries
Також для DieHard 200.71225: Посібник оператора (20 сторінок)
Друкувати сторінку
Itisimportant tounderstand
your c harger's requirements.
This section will t ellyou about
your c harger's electrical requirements
andhow toprepare a battery forcharging.
PLUGGING ITIN
Your c harger requires a 120V AC2-prong
wall o utlet r eceptacle installed according
toalllocal codes a ndordinances.
ASSEMBLING
YOUR CHARGER
Included with your b attery charger aretwo
cord wrap cleats f orstorage oftheclamp
cables.
Toinstall, align the two tabs tocorrespond
with thetwo receptacles
and push until you
hear a snap.
Wrap clamp cables afterunplugging the
power c ordfromtheACwalloutlet a nd
store your c harger inadrylocation.
USING ANEXTENSION
CORD
Theuseofanextension cordis notrec-
ommended.
Ifyoumust u seanextension
cord, p lease make surethatyoufollow
these guidelines:
• Make surethatthepinsoncharger's
power cordfitfirmly intotheextension
cord, a ndthattheextension cordfits
firmly intothereceptacle.
• Check that t he extension cord isproperly
wired andingood electrical condition.
• Make surethatthewiresizeis large
enough f orits length andfortheAC
ampere r ating, asspecified inthechart
below.
MINIMUM RECOMMENDED EXTENSION CORD I
of Cord,
in
Feet
_ ?._ _ 5N _ 1_
15N_
i --
_ --
_ ---N ---i
Length
AWG* Size of Cord
18
16
12
10
• AWG=American
Wire Gauge
It is important
that you read and follow these guidelines
while you are preparing
to charge
the battery.
• Make
sure that you have a 6 or 12 volt
lead-acid
battery.
Determine
voltage
of
battery
by referring
to vehicle
owner's
manual
or the battery
markings.
Charge
battery
initially at charger's
lowest rate.
• Clean the battery terminals.
Be careful to
keep corrosion
from getting
in or around
your eyes or on your hands.
• Wear safety glasses. See additional
"Per-
sonal Safety
Precautions"
on page 4.
•
If required,
for batteries
with removable
vent caps, add distilled
water to each cell
until the battery
acid reaches
the level
recommended
by the manufacturer.
This
will help purge excessive
gases from the
cells. Be careful notto overfill.
If you have
a sealed battery with non-removable
vent
caps, no action is necessary.
• Take
time
to
read
all of the
battery
manufacturer's
specific
precautions,
such as removing
or not removing
vent
caps while charging,
and recommended
rates of charge.
• Be sure
that the area around
the bat-
tery is well ventilated
while
it is being
charged.
Gas can
be forcefully
blown
away
by using a piece
of cardboard
or
other nonmetallic
material
as a fan.
• If it is necessary
to remove
the battery
from
the
vehicle
to charge
it, always
remove
the grounded
terminal
from the
battery
first. Turn off all vehicle
acces-
sories to avoid sparks
from occurring.
• NOTE:
A marine
(boat)
battery
installed
in a boat must be removed
and charged
on shore.