DieHard Portable Power 950 Посібник користувача - Сторінка 4
Переглянути онлайн або завантажити pdf Посібник користувача для Автомобільний зарядний пристрій DieHard Portable Power 950. DieHard Portable Power 950 9 сторінок. 12v dc power source and jump starter
Також для DieHard Portable Power 950: Посібник оператора (9 сторінок), Посібник оператора (9 сторінок), Посібник оператора (13 сторінок), Посібник оператора (7 сторінок)
Друкувати сторінку
WARNING: Failure t ofollow instructions
may cause d amage oranexplosion. Read
entireinstruction m anual b eforeuse.
Always s hield eyes during useandwear
safety g lasses.
JUMP-STARTING
A VEHICLE
ENG|NF
Use in welt-ventilated
area. Keep hands,
hair, clothing
and jewelry
clear of fan
blades, belts, pulleys and other parts that
may cause injury.
1.
Turn ignition off before making cable
connections.
2.
Rest the 950 on a flat, stable surface
near the vehicle battery
and away
from moving engine parts.
3.
Connect the red clamp to the positive
terminal of the vehicle battery.
4.
Connect the black clamp to an un-
painted
and unmoving
part of the
vehicle chassis or engine block.
CAUTION: If you have connected the
clamps backwards,
an audio alarm
wilt sound. Reverse the connections
and the audible alarm will stop.
NOTE:
If after following
steps 1-4
the display remains blank, check for
a good connection
on both jaws of
the clamps. If the display still doesn't
light, hold down the display switch for
5 seconds. If the display doesn't blink,
the external battery voltage is too low
to be detected by the 950.
5.
Digital Display: The charge percent-
age of the vehicle's
battery wilt be
displayed for 5 seconds. The display
wilt blink to indicate proper connection
and will then show the charge per-
centage of both batteries combined
(950 and vehicle)
6.
Turn the key and crank the engine.
The display
wilt count
down from
10 seconds.
If the engine does not
start, wait at least 1 minute before
attempting to crank the vehicle again.
This permits the battery and relay to
cool down. Only attempt to crank the
engine when the display is blinking
(relay is engaged).
7.
Due to a unique safety feature, the
clamp power is automatically
shut
off 10 seconds
after the engine
starts. This eliminates the problem of
sparking when removing the clamps.
Remove and store the clamps
on
the ears located on the back of the
case.
8.
Charge the 950 as soon as possible
after jump-starting.
CAUTION: To prevent sparking, NEVER
allow the clamps
to touch together
or
to contact
the same
piece of metal.
And, never attempt to charge
a frozen
battery.
NOTE: In the rare case of jump-starting
a vehicle that has a positive-grounded
vehicle electrical
system,
connect
the
black clamp to the negative terminal of
the vehicle battery.
Then connect
the
red clamp to an unpainted and unmov-
ing part of the vehicle chassis or engine
block. If you are unsure of the nature of
the vehicle's electrical grounding system,
check the owner's manual of the vehicle
or call the Customer Technical Assistance
number: 1-800-SEARS-64.
POWERING
A 12V DC DEVICE
The Portable
Power
950 is a power
source for all 12 volt DC accessories
that
are equipped with a 12V accessory plug.
The DC accessory
outlet has a 15-amp
automatic
overload
protection
circuit
breaker. The breaker will automatically
reset after an overload occurs.
To operate a 12V DC device:
1.
Open the protective cover of the DC
power outlet on the front panel of the
Portable Power 950.
2.
Plug the 12V DC device into the DC
power outlet, and turn on the 12V DC
device (if required).