ACCURATE ELECTRONICS 1040120000 Посібник
Переглянути онлайн або завантажити pdf Посібник для Комп'ютерне обладнання ACCURATE ELECTRONICS 1040120000. ACCURATE ELECTRONICS 1040120000 6 сторінок. 4-wire 6-way active conference bridge
Друкувати сторінкуPO BOX 1654 97075-1654
8687 SW HALL BLVD 97008
4-WIRE 6-WAY ACTIVE CONFERENCE BRIDGE
CONTENTS:
Section 1. General
Section 2. Features
Section 3. Application
Section 4. Installation
Section 5. Options
Section 6. Circuit Description
Section 7. Mechanical Outline
Section 8. Specifications
Section 9. Testing and Troubleshooting
Section 10. Maintenance
Section 11. Warranty
Figure 1. Typical Application
Figure 2. Circuit Description
Figure 3. Mechanical Outline
Figure 4. External Connections Layout
Figure 5. Testing Guide Checklist
1. GENERAL
1.01 This practice provides application, specification, circuit and mechanical
description, maintenance, installation, and warranty information relating to
Accurate Electronics' 4-wire 6-way Conference Bridge, Model 10401200.
2. FEATURES
Designed for voice conference applications for full 6-way
bridging of 4-wire transmission facilities.
Can be used with voice (VF) or data up to 9.6 kbps.
This document contains proprietary information and is supplied for identification, maintenance, engineering evaluation or inspection purposes only and shall not be duplicated or disclosed without written
permission of: ACCURATE ELECTRONICS INC By accepting this document the recipient agrees to make every effort to prevent unauthorized use of this information.
Prac_10401200_RevA.pdf
ACCURATE ELECTRONICS INC
BEAVERTON OR USA
WWW.ACCURATE.ORG
MODEL 1040120000
1
1
1
2
2
2
3
3
3
3
3
1
4
4
5
5
503.641.0118
FAX 503.646.3903
Practice Section 10401200 Rev A
Zero dB loss bridge, with an adjustable gain of - 10 to + 22dB
(receive-to-transmit).
Selectable 7 dB (receive) and -16 dB (transmit) pads for each
bridge port, which allows proper interfacing with carrier
facilities.
Front-panel-mounted RX and TX calibration Bantam jacks, for
simplified alignment.
SX leads for each transmit and receive port.
Can be powered from - 48 VDC. (-22 TO -56 VDC)
3. APPLICATION
3.01 Model 10401200 is a 4-wire 6-way Active Conference Bridge. A voice
(VF) or data signal received at any receive port is transmitted to all other
transmit ports (minus the associated transmit port), providing leg to leg
communication. Front-panel-mounted transmit and receive gain adjustments
are provided for each bridge port. Proper adjustment allows all signals on the
bridge to be transmitted and received at the same level.
3.02 Model 10401200 mounts in one module mounting position of a Type 10
or 400 Relay Rack Shelf. They make electrical connection to the system via
a 56-pin, wire-wrapped, card-edge connector, provided as part of the shelf
mounting assembly.
3.03 The Model 10401200provides jumper selected insertion loss of -7dB in
each receive port and -16dB in each transmit port to facilitate interfacing with
carrier channel or other standard level 4wire interface (+7dB receive, -16dB
transmit). When lossless bridging is required, the 0dB jumper positions may
be selected.
3.04 Terminating impedance at both the input and output ports of the bridge
is 600 ohms, balanced. The modules' active circuitry allows unused ports to
be left unterminated without affecting transmission performance of the ports
in use.
3.05 The bridge module incorporates an internally regulated power supply
that permits operation on -22 to -56 VDC input. Current requirement is 60mA
when powered from a nominal -48VDC power source. Reverse-battery
protection is provided in the modules' internal power supply circuits.
Figure 1. Typical Application.
Page 1 of 6
Model 10401200
January 2014