CIOKS 4 Посібник користувача - Сторінка 2

Переглянути онлайн або завантажити pdf Посібник користувача для Подовжувач CIOKS 4. CIOKS 4 2 сторінки. Power supply for effect pedals

Друкувати сторінку

Overview

Left

On the left side you will find the USB C and the non-polarized DC input sockets and the four RCA sockets

being outlets 1-4 for powering pedals.

Top

CIOKS logo has a red LED placed in the middle of the letter 'O' and this functions as a global status

indicator. For each outlet you have a voltage selector switch and an advanced LED indicator.

Front

The two holes in the front with metric M4 threads are to be used with the Mini GRIP bracket (sold

separately) for mounting to Pedaltrain boards with no drilling required.

Bottom

The four detachable rubber feet are situated on the bottom of the enclosure. On this same surface you will

find 3 holes with metric M4 threads which should be used for mounting of the power supply to a

pedalboard.

Getting started

Connect a supply voltage to CIOKS 4 power supply within the specified type and range. Set the output

voltage on a given outlet to either 9, 12, 15 or 18V depending on the needs of the particular pedal to be

powered. Using the right Flex cable type connect your pedal to this outlet. Repeat this with your remaining

pedals.

Advanced LED Monitoring feature

Each isolated outlet has its individual LED status indicator. The indicator is lit in normal operation. The

LED light gets dim when you operate just on the edge of the current mA limit for the voltage you have

chosen on the given outlet. If you overload or short circuit an outlet, the respective LED indicator turns off.

The light intensity of the status LED will be higher when the output voltage is set to a higher value than 9V

being 12, 15 or 18V.

Global status indicator

If COKS 4 power supply is powered of a solid power source sufficient to provide enough power and

everything functions normally the red LED inside the O letter in CIOKS logo will be lit. If the source

supplying CIOKS 4 power supply is too weak and the voltage on the input of CIOKS 4 is too low the

indicator will turn off.

Pedalboard mounting

General

The most solid way is using the drill template being the product sheet and then drill two diagonally

positioned ø4,5mm or ø5,0mm holes in the pedalboard and fasten the CIOKS 4 to it with the two included

screws. Due to CIOKS 4 extremely flat profile and low weight you can use Dual-Lock tape or industrial

Velcro to fasten it below any type of pedalboard. In general for mounting in a rack, pedalboard or other

structure we recommend using two of the five threaded M4 holes (3 in the bottom and 2 in the front) and

matching metric M4 screws. Remember not to penetrate the CIOKS 4 with more than 5mm with the screws

used.

Pedaltrain

For Pedaltrain boards we recommend an easy alternative way of mounting CIOKS 4 unit by using the Mini

GRIP bracket where no drilling is needed.

Version 1.03

Temple Audio

The three threaded M4 holes in the bottom of CIOKS 4 are aligned with the grid of Templeboards and

allow for very easy mounting on top or below any Temple Audio pedalboard with the included 2 screws.

We recommend using the two holes positioned diagonally. If you want to make a distance between the

board's surface and the CIOKS 4 to allow space for the Temple Audio finger screws you should get a set

of three 8mm hex stand-offs with matching screws (order no. 4HEX) and then use these with all three

threaded holes in the bottom of the power supply.

Included accessories

Flex cables

CIOKS offers a wide selection of different Flex cable types for connection your pedals to the power

supply. Below you see a list of the included Flex cables with your unit:

•

Standard Flex type 1 – black with 5,5/2,1mm centre negative DC plug

•

3-way daisy chain Flex type 1 – black with three 5,5/2,1mm centre negative DC plugs x1

The 3-way daisy chain Flex should be used if you wish to power three pedals with the same voltage using

only one outlet. For further information about all CIOKS Flex cables please have a look at the included

Flex cable selection guide or visit CIOKS web site.

DC Link cable

A DC Link cable in 50cm length is included and should be used to connect CIOKS 4 power supply to

CIOKS DC7 power supply's 24V DC outlet. You can also use this cable to connect and power CIOKS 4

of another compatible 24V DC source.

Mounting hardware

We have included all the needed mounting hardware to mount the power supply on top or underneath a

Pedaltrain or a Temple Audio pedalboard. You can of course also attach it to other types of pedalboards.

CIOKS 4 output power capability

A solid DC source of minimum 17V DC is needed to obtain full 24W of output power capability from

CIOKS 4. If a lower voltage is applied to the DC input socket or you are powering the unit of a USB

source its output power capability will be lower than the 24W. The table below shows the maximum

output power of CIOKS 4 depending on the type and voltage of power source which is used to power it.

Input

December 2019

Version 1.03

Input voltage

Input current

Output power

9V DC

12V DC

15V DC

>17V DC

max. 2A

max. 24,0W

9V AC

12V AC

5V DC

Total output

current @ 9V

10,8W

1200mA

15,3W

1700mA

19,8W

2200mA

max. 2640mA

6,3W

700mA

10,8W

1200mA

6,3W

700mA

9,0W

1000mA

December 2019