CipherLab RS50 Посібник із швидкого старту
Переглянути онлайн або завантажити pdf Посібник із швидкого старту для Зарядний пристрій CipherLab RS50. CipherLab RS50 2 сторінки. Charging & comm. cradle
Також для CipherLab RS50: Посібник із швидкого старту (2 сторінок)
Друкувати сторінку
RS50 Mobile Computer
Quick Start Guide
Download the user manual and CD contents using GoBetween, available at:
http://ccs.cipherlab.com
.
Open Your Box
aRS50 Mobile Computer
2
1
a
Rechargeable Li-ion battery
3
a
Wrist Band
a
Quick Start Guide
a
Snap-on Charging and Communication Cable
a
AC Power Adapter
8
4
5
7
18
17
16
6
15
9
10
1. Status LEDs (left: charging, right: Notifications)
11. Volume Keys
2. Light sensor
12.
Loudspeaker
3.
Phone Receiver
13.
Battery Latch
4.
Power Button
14.
Wrist Band Hole
5.
Side Keys
15. NFC Detection Area
6.
Charging & Communication Port
16. Battery (with Cover)
7.
Microphone
17. Camera Flash
8. Touch Screen
18. Camera Lens
9. Scan Window
19. Rear Microphone
10. Headset Jack
Important Charging Information
Power Supply
Input: AC 100-240V, 50/60Hz; output: 5V/2A, CipherLab approved
3.8V, 4000
mAh 3.75V,
/
5300mAh rechargeable Li-ion,
Battery PacK
CipherLab proprietary
Charging Time
Approx. 5/6 hours via adapter
www.cipherlab.com
EN
Install/Remove Battery
2
1
2
19
14
Install SIM, SAM and SD Card
11
Step 1:
12
Remove the battery.
Step 2:
13
Insert your fingernail into the notch above the
inner lid that protects the card sockets chamber,
and then lift it up.
Step 3:
After the chamber is revealed, insert SIM cards, the SAM card and
the microSD card into their respective sockets. Close and push
14
back the hinged cover till a "click" sounds.
SIM1
SAM
Step 4:
Replace the inner lid.
Step 5:
Replace the battery.
To Install the Battery
Fix the lower edge of the battery first, and then press the top of it
in. You will hear the latch click in to place. Keep Pressing the
battery till you lock the latch.
To Remove the Battery
1
Unlock
Step 1:
Slide the battery latch to the
Right,
the battery will be unlocked
with a "click" sound.
Step 2:
Lift the battery up from its upper end.
Inner Lid
SIM2
To install the cards:
1)Slide the hinged cover back.
2)Swing the top open, and
then insert the card.
3)Close the
hinged cover,
and then push it back.
2
MicroSD
EN
Charging & Communication
Charging and data communication of the RS50 mobile computer can be performed via Snap-on
Charging & Communication Cable.
Step 1:
Attach the Snap-on Cable to the mobile computer.
To connect the Cable:
The pins on the bottom of this device serve as the sole
Charging & Communication port; slightly fasten the Cable to
the port, and you will hear a "click" when it is well connected.
To disconnect the Cable:
Pull the right tab of the connecting cup
slightly outwards to detach the cable.
1
Step 2:
For data transfer, plug the opposite end of the cable to your PC.
Step 3:
For battery charging, plug
the opposite end of the cable
plug the adapter into the
electrical outlet. The charging LED on the mobile computer lights up in red
(battery low, charging), and turns green to indicate charging is almost complete.
EN
Charging & USB Communication Port
PULL
OPEN
2
into the supplied power adapter, and then
3