Arcam AVR200 Посібник - Сторінка 8

Переглянути онлайн або завантажити pdf Посібник для Приймач Arcam AVR200. Arcam AVR200 19 сторінок. Surround sound receiver
Також для Arcam AVR200: Посібник з експлуатації (15 сторінок)

Друкувати сторінку
Arcam AVR200 Посібник

Setting up

Using the On Screen Display (OSD)

The easiest way to set up the AVR200's multi-channel audio and
video options is through its On Screen Display (OSD).
To enter the OSD, ensure that you have a TV connected and
press any of the arrows on the remote control's cursor pad.
To navigate from the fi rst (i.e. Setup) page, use the
arrows to highlight a line. To enter a highlighted page, press
To leave the OSD, highlight 'EXIT' and press
Once on a page, use the
and the
happy with the settings, highlight 'SAVE AND EXIT' and press
to keep them in memory. If you are unsure about the changes,
or you have entered the page accidentally, highlight 'DO NOT
SAVE AND EXIT' and press
are ignored.

Setup page

The Setup page forms the index to the OSD. To navigate from
here, use the cursor pad on your remote control.

Input settings page

AUDIO
VIDEO
MODE
DYNAMIC RANGE
CENTRE WIDTH
AVR200
8
and
arrows to move to a line
and
arrows to change an option. Once you are
•
and any changes on that page
OK
Identifi es the active audio source (e.g. CD)
Identifi es the active video source (e.g. DVD)
Identifi es the surround mode associated with
the current input (Dolby Digital, DTS, Dolby
Pro Logic II Movie, Dolby Pro Logic II Music,
Dolby Pro Logic II Panorama, Dolby Pro Logic II
Matrix, Dolby Pro Logic, Hall effect or Stereo)
A compressed dynamic range is useful for low
level (night time) listening. For Dolby Digital
sources, the dynamic range has options of
100%, 75%, 50% or 25%
(Dolby Pro Logic II Music Mode only)
Allows centre-channel sounds to be positioned
between the centre speaker and the left/right
speakers over a range of eight steps. Step '3'
uses a combination of all three front speakers
to give the best vocal imaging and most
seamless soundstage and is recommended for
most recordings. Step '0' places all centre
sound in the centre speaker. Step '7' places all
centre sound equally in the left/right speakers,
as in conventional stereo.
Setting options for CENTRE WIDTH
DISPLAY
Off
1
2
3
4
5
6
7
NOTE: In some cases you may fi nd that the OSD is not still
or that it 'rolls over' your screen. (You may also notice this
effect when the volume bar is shown on screen.) If this is
the case, you will need to switch the video system being
and
used by the AVR200.
.
OK
To do this, fi rst exit the OSD by highlighting
.
OK
OK
the AVR200 then toggle between the systems shown in the
display area by pressing the
OK
North America) or PAL (used in most of Europe) – until the
correct system is selected.
69.8°
EFFECT
No Centre spreading
20.8°
28°
36°
54°
62°
69.8°
Phantom Centre
. Press and hold the
button on the front panel of
STORE
button – NTSC (used in
SAT
SETUP
1
INPUT SETTINGS
2
CHANNEL BALANCE
3
CHANNEL DELAYS
4
SPEAKER SETTINGS
5
EXIT
SETUP
1
INPUT SETTINGS
2
CHANNEL BALANCE
3
CHANNEL DELAYS
4
SPEAKER SETTINGS
5
EXIT
front
centre
left
62°
54°
36°
28°
20.8°
and press
EXIT
INPUT SETTINGS
AUDIO = DVD
VIDEO = DVD
MODE = DOLBY DIGITAL
DYNAMIC RANGE = N/A
CENTRE WIDTH = 3
DIMENSION = 0
DO NOT SAVE AND EXIT
SAVE AND EXIT
front
right
69.8°
62°
54°
36°
28°
20.8°