Axvue HD-992 Інструкція з експлуатації

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Радіоняня Axvue HD-992. Axvue HD-992 2 сторінки. Video baby monitor with 5" hd lcd screen & 2 cameras

Друкувати сторінку

INSTRUCTION MANUAL

AXVUE HD992 VIDEO BABY MONITOR

WITH 5" HD LCD SCREEN & 2 CAMERAS

Please read the following instructions and warnings carefully

Keep this instruction manual for the future.

For technical support see the FAQ page.

For adult use only.

FEATURES & COMPONENTS

Camera:

1. Night-Vision LED

2. Lens

3. Temperature Sensor

4. Microphone

Monitor:

Power & Low Battery

Adapters:

× 1

Revised at 9/2020

Get to know us at: www.axvue.com

keep the distance

between sensor and body

at least 0.6 inch for

accurate temperature

result

0.6 in

5. Speaker

6. Power/Code

7. DC Jack

8. Wall Mounting Hole

1. LED

2. MENU

3. Pan / Tilt

4. Motion Detection

5. Zoom / Talk Back (OK)

6. Volume

7. Brightness

8. Cam / Split

9. VOX

10. Microphone

11. Speaker

12. Battery Compartment

13. Kickstand

14. Power / Video

15. DC Jack

*LED

Sound Lights

× 2

× 3

× 2

WARNING

THIS PRODUCT CAN NOT SUBSTITUE PARENT'S SUPERVISION ON YOUR CHILD.

Model- HD992

- Store this product out of the reach of babies (at least 3 feets (0.9 m) away from the crib). A strap

wound around the baby's neck may result in asphyxiation. Use a safety clip to clamp the power cord

and keep it out of baby's reach. Do not use other extension cords. Only use the power adapter

provided.

- Do not touch the exposed part if the adapter is connected with power.

- Test regularly before initial use or when change the position of camera.

- Avoid placing the product in humid place or contacting with liquid. (such as bathtub, sink, etc.)

- Do not apply heat to the product.(such as stoves, radiators, etc.)

- Using the product in ventilated place. Avoid placing it on sofas, cushions, beds or other places which

may block ventilation.

- The product only can be operated by adult. Do not allow baby to play with it. Tiny accessories are

contained, please be careful when unpack and install it.

BATTERY WARNING

- Only use the recommended rechargeable battery. Please contact us if you need to change it.

For the contact list, please refer to the last page of the instruction.

- Please clean the battery compartment before using it.

- Avoid short circuits the power supply terminal.

- Remove the battery when you are not using it or when running out of power.

- Keep the battery away from children.

- Dispose of the empty battery properly.

WARNING

Asphyxiation Danger:

crib). A strap wound around the baby's neck may result in asphyxiation. Use a safety clip to clamp the

power cord and keep it out of baby's reach. Do not use other extension cords. Only use the power

adapter provided.

SETUP & USE

Please charge the battery for at least 8 hours before

using the product.

Step 1: Test reception ﬁrst, put the camera in a suitable place that

will provide you the best view of your baby in the crib (Note: Do

not hang up the camera ﬁrmly until the initial installation test is

completed). Plug the adapter into the wall outlet and turn on the

camera.

Step 2: Turn on the monitor by pressing and holding the Power /

Video"

" button for 5 seconds until "axvue" shows up, then

the video will show up on the screen immediately. If the video

does not show up, please refer to "TO PAIR MONITOR AND

CAMERA (ADD CAMERA)" on the next page. If the video shows

up, the initial installation test is completed, then you can set up

the camera according to the instruction below.

Set Up Camera: Place the camera on a ﬂat surface, such as a

wardrobe or shelf (Figure 1). Or hang it on the wall (Figure 2). No

matter wherever to place the camera, please make sure to keep it

away from the crib for at least 3 feet and all power cords should be

placed behind the camera properly. Then adjust the angle of the

camera lens until the entire crib shows up on the display, or adjust

it to the best angle that you think to watch your baby.

TO USE PLUGGED-IN MODE

Step 1: Place the monitor display in the living room, bedroom or any place you want to watch your

baby. Use an adapter to connect the camera with an electrical outlet.

Step 2: Turn on the monitor by pressing the Power / Video"

logo or video shows up on the screen.

Step 3: Press Power / Video"

Step 4: Turn oﬀ the monitor completely by pressing and holding the Power / Video"

for 5 seconds.

TO USE PORTABLE / BATTERY MODE

Please charge the battery for 6 ~ 8 hours before using the product.

Step 1: Charge the battery for at least 8 hours before using portable / battery mode.

Step 2: Make sure the adapter is plugged into the camera.

Step 3: The battery life can be up to 15 hours if it is fully charged.

Battery life will be shortened if recharging it continuously. Unplug the power adapter when you are

not using it for a long time.

TO PAIR MONITOR AND CAMERA (ADD CAMERA)

The monitor and camera are paired before shipment. If it is unpaired for some reason, please refer

to the following steps:

Step 1: Make sure the camera and monitor are in the same place.

Step 2:

× 12

Step 3:

× 2

Step 4:

Store this product out of the reach of babies (at least 3 feet away from the

" button for 5 seconds until axvue

" button to turn oﬀ the video if you only need to hear the voice.

Make sure the power adapter is plugged into

３

camera and turn on the camera by pressing

Power / Code"

" button for 3 seconds.

Figure 1

3 feet

Figure 2

" button

Turn on the monitor by pressing

and holding Power / Video

" button for 5 seconds.