Digicel VM1510 Посібники з швидкого старту
Переглянути онлайн або завантажити pdf Посібники з швидкого старту для Приставки для телевізорів Digicel VM1510. Digicel VM1510 2 сторінки.
Друкувати сторінкуInstallation
Front Panel
1
2
3
4
5
3305-00550_MANUAL_DIGICEL_QUICK GUIDE_ENG_ .indd 1
QUICK START Guide
DIGICEL VM1510
Please read this installation guide carefully before you use this product and
Power indicator ( )
The indicator light turns red when the power turns on.
6
Remote control signal sensor (
Do not block IR receiver, so that you can use the remote
control properly.
Lock indicator (
)
CH
Channel Up/Down (up and down key)
VOL
Volume Up/Down (up and down key)
POWER
Switch the receiver power "ON" or "OFF".
Safety information
Safety information
Digicel is not responsible for problems caused by misuse of equipment.
Digicel is not responsible for problems caused by misuse of equipment.
Precaution
Place your product on a stable surface.
Precaution
Do not drop or hit your product. This may cause a malfunction or injury.
Do not leave your product in too high or low temperature for a long time. Doing so may cause an explosion or an
Place your product on a stable surface.
electric shock.
Do not drop or hit your product. This may cause a malfunction or injury.
FCC STATEMENT
Caution : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for
Do not leave your product in too high or low temperature for a long time. Doing so may cause an explosion or an
compliance could void the user's authority to operate the equipment.
electric shock.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
2_ENG
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
2_ENG
ENG_1
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment. Indoor use only.
This appliance and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. A minimum separation
distance of 20 ㎝ must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirements
Installation
Rear Panel
1
2
3
4
)
LOOP OUT
Used to connect an antenna signal from the receiver
to either the antenna input jack on your television or
to another receiver.
ANT IN
AUDIO
Audio connection port to the TV or other equipment.
CVBS
Video connection port to the TV or other equipment.
ENG_3
4_ENG
5
6
7
8
9
DC 12V Power connection
S/PDIF
Connect a digital amplifer output.
HDMI
Connect your decoder to an HDTV set with an HDMI cable
ETHERNET
Connect the LAN cable to Ethernet port.
USB
Connect the USB memory device to USB port
DC 12V IN
To connect your decoder to the main power supply.
2014-11-24
1:29:06