Epson 2180 - LQ B/W Dot-matrix Printer Посібник - Сторінка 23
Переглянути онлайн або завантажити pdf Посібник для Принтер Epson 2180 - LQ B/W Dot-matrix Printer. Epson 2180 - LQ B/W Dot-matrix Printer 30 сторінок. Impact printer
Також для Epson 2180 - LQ B/W Dot-matrix Printer: Технічні характеристики (2 сторінок)
Друкувати сторінку
Advancing the Paper to the Tear-Off Edge
If you use the front or rear push tractor, you can use the tear-
off feature to advance your continuous paper to the printer's
tear-off edge when you finish printing. You can then easily
tear off the printed document. When you resume printing, the
printer automatically feeds the paper back to the top-of-form
position so that you can save the paper normally lost between
documents.
As described below, you can use the tear-off feature in two
ways: manually by pressing the printer's
or automatically by turning on the auto tear-off mode.
If the perforation between pages is not aligned with the tear-
off edge, you can adjust the position of the perforation using
the micro adjust feature. For instructions, see "Adjusting the
tear-off position" on this page.
Caution:
Never use the tear-off feature (by pressing the Tear Off/
Bin button or turning on the auto tear-off mode as
described below) to feed continuous paper with labels
backward; they may come off their backing sheet and
jam the printer.
Using the Tear Off/Bin button
After the printer finishes printing your document, check that
the
lights are not flashing. Then press the
Tear Off/Bin
button. The printer advances the paper to the tear-off
Off/Bin
edge.
Note:
If the Tear Off/Bin lights are flashing, the paper is in the tear-off
position. If you press the Tear Off/Bin button, the printer feeds your
paper to the next top-of-form position.
Advancing paper to the tear-off position
automatically
To automatically advance your printed documents to the tear-
off position, you need to turn on the auto tear-off mode and
select the appropriate page length for continuous paper in the
default-setting mode. For instructions, see "About Your
Printer's Default Settings" on page 26.
When auto tear-off is on, the printer automatically advances
the paper to the tear-off position whenever it receives a
full page of data or a form feed command followed by no
more data.
button,
Tear Off/Bin
Tear
2/99
Adjusting the tear-off position
If your paper's perforation is not aligned with the tear-off
edge, you can use the micro adjust feature to move the
perforation to the tear-off position. Follow the steps below.
Caution:
Never use the knob to adjust the tear-off position while
the printer is turned on; this may damage the printer or
cause it to lose the tear-off position. The knob can be
used when the printer is turned off only.
Note: Your tear-off position setting remains in effect
until you change it, even if you turn off the printer.
1. Make sure the
Tear Off/Bin
at the current tear-off position). You may need to press the
button to advance the paper to the tear-off
Tear Off/Bin
position.
2. Open the paper guide cover.
3. Hold down the
Pause
light begins flashing and the printer enters the micro
Pause
adjust mode.
4. Press the
D button to feed the paper backward, or
LF/FF
press the
U button to feed the paper forward
Load/Eject
until the paper perforation is aligned with the tear-off edge.
Note:
The printer has a minimum and a maximum tear-off position. If
you try to adjust the tear-off position beyond these limits, the
printer beeps and stops moving the paper.
5. After you set the tear-off position, press the
to turn off the micro adjust mode.
6. Tear off the printed pages.
When you resume printing, the printer automatically feeds the
paper back to the top-of-form position and begins printing.
EPSON LQ-2180
lights are flashing (the paper is
button for about three seconds. The
tear-off-edge
Pause
EPSON LQ-2180
button
- 23