Circuit ECX03011AU Інструкція з експлуатації - Сторінка 11

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Іграшкова машинка на колесах Circuit ECX03011AU. Circuit ECX03011AU 19 сторінок. 1/10 4wd electric stadium truck

Друкувати сторінку

BINDING

Binding is the process of programming the receiver to recognize

the GUID (Globally Unique Identiﬁ er) code of a single speciﬁ c

transmitter. The DX2E and SR201 receiver are bound at the fac-

tory. If you need to rebind, follow the instructions below.

1. With the receiver off, insert the bind plug into the BIND port

on the receiver.

2. Power the receiver through any other port. The orange LED

will flash continuously, indicating the receiver is in bind mode.

3. With the steering wheel and throttle trigger in the failsafe

positions, normally full brakes and straight steering (see the

Failsafe section on this page for more information), press and

hold the bind button and turn on the transmitter. The green

LED on the front of the transmitter will flash within three

seconds, indicating the transmitter is in bind mode.

4. Release the bind button when the green LED flashes.

Continue to hold the steering wheel and throttle trigger in the

failsafe positions until the LED on the receiver glows solid.

Bind Button

TROUBLESHOOTING GUIDE

Problem

Short Run Time

• Battery damaged/not charged

• Motor dirty or brushes worn

Sluggish Action

• Motor dirty or brushes worn

• Bind in drivetrain

• Vehicle battery is not charged

Controls Reversed

• ST. REV or TH. REV

Motor/ESC overheat

• Over-geared for the driving environment

Doesn't Operate

• Transmitter batteries low

• Transmitter powered off

• ESC powered off

• Vehicle battery is not charged

Poor Range

• Transmitter batteries low

• Receiver antenna damaged

The system will not

• Transmitter and receiver too near each other

connect

• Transmitter and receiver too near large

• Receiver accidentally put in bind mode so

The receiver goes into

• Check the receiver antenna to be sure it is

failsafe mode a short

distance away from the

transmitter

The receiver quits re-

• Low battery voltage

sponding during operation

• Loose or damaged wires or connectors

Receiver loses its bind

• Transmitter accidentally put in bind mode,

Possible Cause

metal objects (vehicles, etc.)

receiver is no longer bound

not cut or damaged

between battery and receiver

ending bind to receiver

5. The LED on the receiver will glow solid when the transmitter

and receiver are bound.

6. Remove the bind plug and store it in a convenient place.

You must rebind when:

• Different failsafe positions are desired e.g., when throttle or

steering reversing has been changed.

• Changing receiver types e.g., changing from a DSM

to a DSM2

or Marine receiver.

• Binding the receiver to a different transmitter.

Some Spektrum receivers, like the SR3001, use a bind button

rather than a bind plug. The binding process is the same with

this receiver, however, instead of inserting the plug before

powering up the receiver, press and hold the bind button while

powering up the receiver to enter bind mode.

FAILSAFE

In the unlikely event that the radio link is lost during use, the

receiver will drive the servos to their preprogrammed failsafe

positions (normally full brakes and straight steering). If the

receiver is turned on prior to turning on the transmitter, the

receiver will enter failsafe mode, driving the servos to their

preset failsafe positions. When the transmitter is turned on,

normal control is resumed. Failsafe servo positions are set

during binding (see binding a receiver above).

• Check/change battery

• Check/clean/replace

• Clean/adjust

• Replace/recharge

• Change switch position

• Install smaller pinion

• Replace/recharge

• Power On

• Replace/recharge

• Check/repair/replace

• Move transmitter 8–12 feet (2.4–3.6m) from receiver

• Move away from large metal objects (vehicles, etc.)

• Rebind transmitter and receiver

• Contact Horizon Product Support

• Make sure receiver antenna is in an antenna tube

and is above vehicle

• Completely recharge battery

• Do a check of the wires and connection between

battery and receiver. Repair or replace wires and/or

connectors

• Bind transmitter to receiver

receiver

Solution