Epson 980N - Stylus Color Inkjet Printer Інформаційний посібник про продукт - Сторінка 7
Переглянути онлайн або завантажити pdf Інформаційний посібник про продукт для Принтер Epson 980N - Stylus Color Inkjet Printer. Epson 980N - Stylus Color Inkjet Printer 14 сторінок. Warranty statement
Також для Epson 980N - Stylus Color Inkjet Printer: Технічна специфікація (2 сторінок), Технічні характеристики (2 сторінок), Інформаційний листок продукту (4 сторінок), Оновлення (1 сторінок), Обмежена гарантія (1 сторінок)
Друкувати сторінку
4. Hold down the E load/eject button, then press and release
the Ppower button. Continue holding down the E load/
eject button until the Ppower light starts to flash, then
release it.
The printer prints one page showing its ROM version
number, ink counter, and a nozzle check pattern in black,
magenta, cyan, and yellow. Only the nozzle check pattern is
shown below.
5. To end the check, turn off the printer after it prints the
check page. Then reconnect the interface cable and turn on
your printer and computer.
If the results are satisfactory, the problem lies in your
software settings, the interface cable, or your computer.
If the check page does not print correctly, you may have
a problem with your printer. First try cleaning the print
head (see page 11). Then try the suggestions in
"Problems and Solutions" in the Printer Basics book or
"Troubleshooting" in the electronic EPSON Stylus
COLOR 980N Reference Guide.
Printing an Ethernet Card Status
Sheet
Press and hold down the status sheet button for about three
seconds to print a status sheet. This sheet gives you important
information, including the serial number and MAC address
(hardware address) of the card. (Save the sheet for reference.)
If a status sheet prints, the Ethernet card is working correctly.
status sheet button
Reading the Ethernet Card Status
Lights
The status lights and status sheet button provide you with
important information about the operation and configuration
of the Ethernet card.
The Ethernet card has two status lights (one red and one
green) that indicate the current operating status of the
Ethernet card when you first turn on the printer, during
normal operation, and when errors occur. The card also has a
link selection light (yellow) that shows whether 10 Base T or
100 Base TX is connected.
The red and green lights represent the following:
Red
Green
Flash simultaneously
Off
Flashes
slowly
Off
Flashes
rapidly
Off
On
On
Off
The yellow link selection light represents the following:
Light
Off
On
Initializing the Ethernet Card
You must initialize the Ethernet card under the following
circumstances:
If you move the card to another printer
When there is an error communicating with the
Ethernet card.
Follow these steps to initialize the Ethernet card:
1. Turn off the printer.
It will take several seconds for the Ethernet card to power
down. Wait until the status lights on the card go out before
continuing with step 2.
2. Turn on the printer while holding down the status sheet
button. Continue to hold down the status sheet button for
about five seconds.
When the red and green status lights on the Ethernet card
start to flash simultaneously, release the status sheet button.
Initialization is complete when the status lights stop
flashing.
3. After initialization is complete, press and hold down the
status sheet button for about three seconds to print a status
sheet. If the card initialized properly, the TCP/IP address
on the status sheet will be 192.168.192.168 and the printer
name will be <default printer name> <last six digits of the
serial number>.
10/00
EPSON Stylus COLOR 980N
Status
Initializing status at power on or reset
Printing data or the status sheet
Sending and receiving packets
Normal ready status
Error status
Status
10 Base T
100 Base TX
EPSON Stylus COLOR 980N
- 7