Cressi 30628 Інструкція з використання - Сторінка 15
Переглянути онлайн або завантажити pdf Інструкція з використання для Водолазний інструмент Cressi 30628. Cressi 30628 19 сторінок. B.c. 's jackets
Друкувати сторінку
USE AND DURATION LIMITS
EN
1 -
This BCD must not be used beyond the first 50 metres of depth.
2 - This BCD must only be used with SCUBA diving breathing apparatus
bearing the CE mark.
3 - This BC can be used in water temperatures ranging from -2 °C to + 40 °C.
It can withstand external (ambient) temperatures from –20 °C to + 50 °C.
Diving in extreme conditions, with water temperatures below 10 °C,
is risky for the human body, and you should therefore have taken and
passed specific courses before diving in such conditions.
4 - A buoyancy control device is not a life jacket and may not keep your head
out of water.
5 - If the buoyancy control device described in this manual is used with
Nitrox mixtures containing up to 40% O2, it will require more frequent
and thorough maintenance than with breathable air.
6 - No alterations, even minor ones, can be made to this BCD. Alterations are
prohibited for the purposes of personal health and safety.
7 - For the purposes of personal health and safety, use is prohibited in
polluted water, water with a high level of suspended solids, and in any
liquid with different chemical/physical characteristics to water.
8 - Use of the BCD in chlorinated waters will cause the materials to
deteriorate. It is therefore not recommended for use in water with a high
concentration of chlorine.
30
MAINTENANCE
To maintain your BCD properly, be sure to follow these instructions:
1 - Always carry it in a protective bag.
2 - Avoid contact with sharp or pointed objects, or objects that may cause
abrasions.
3 - Avoid prolonged exposure to sunlight.
4 - At the end of each dive in the sea, lake or pool, always rinse the interior
and exterior with fresh water. For the interior, fill the bladder about 1/3
full through the mouthpiece of the control unit (keeping the drain button
pressed), and then partially inflate and shake it. Empty it by opening the
lower quick dump valve.
5 - Every 4 or 5 dives, clean and lubricate the quick coupling for the hose and
the By-Pass coupling with silicone grease.
6 - Replace the hose seals annually at an authorised Cressi centre.
7 - We recommend getting your BCD inspected annually at an authorised
Cressi centre. In case of intense use (diving centres, rental use, professional
use, or other), we recommend having the BCD serviced every three/six
months at an authorised Cressi centre.
8 - If you need to replace a hose, the new one must be the same type as the
hose supplied at the time of purchase. If you have any doubts about its
characteristics, contact the manufacturer or an authorised retailer.
STORAGE
1 - We recommend storing your BCD in a perfectly dry and partially inflated
state and in a cool and dry place. Ideally, it should be hanging.
2 - The storage location must be removed from sources of heat or direct
sunlight.
3 - Avoid locations where the BCD could come into contact with chemical
products or corrosive agents that could affect its safety features.
4 - Avoid placing other objects on top of it.
5 - Leave the control unit in an extended position. The corrugated hose must
not be bent or crushed.
SIZES
For sizes, see the Fit column of the final table.
NITROX
Do not use this BCD with Nitrox mixtures containing more than 40% oxygen.
The use of mixtures with higher percentages of oxygen, or that contain helium
or other gases (Trimix), could cause corrosion, deterioration or premature
ageing of the BCD or its components, causing them to break. This could result
in a loss of buoyancy control or the BCD losing its seal, leading to serious
physical harm. Mixtures with a high oxygen content can also increase the risk
of ignition and explosion. In order to use Nitrox or Trimix mixtures, you must
obtain, in addition to the diving certification, specific certification, issued by an
internationally recognised educational organisation.