Accusplit Eagle AE140XL Інструкція з експлуатації - Сторінка 3

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Крокомір Accusplit Eagle AE140XL. Accusplit Eagle AE140XL 4 сторінки. Accusplit pedometer operating instructions

Друкувати сторінку

VIEWING YOUR RESULTS

Once you put on your pedometer with the cover closed, it

will automatically begin to record your steps, activity time,

and distance. Repeatedly press the MODE button to cycle

through the pedometer modes:

STEPS g DISTANCE g STEPS

Distance is counted automatically whenever steps are being

counted.

• DISTANCE is simply stride length x steps.

Note: For extra accuracy, the default Step Filter Setting is 1.

See page 19 to learn more.

OTHER SETTINGS

The Step Filter and Unit of Measurement settings are

accessed through a special "deep set" mode.

To enter this mode, press and hold the S1 button for 4

seconds. T he screen will display a single digit. From within

Deep Set mode, press the S2 button to cycle back and forth

between the Step Filter set point and Choice of Unit System.

Can be set

from 0-5

steps

"US" (English)

or "EU" (Metric)

IGI

ALKER

.COM

STEP

DIST

SET

140

JW200

S3-

S1,S2,S4

S3+

Set measurement mode

REPLACING THE BATTERY AND MASTER RESET

When the display starts to dim or goes blank, it is time to

replace the battery.

If the display is not uniformly dim or blank, and appears to

display "erroneous data" , do a Master Reset by pressing all

3 buttons simultaneously for 3 seconds and then release.

The display should go blank, then turn all segments on, then

display 0 steps in Step Mode.

Note: All the settings will return to their default setting values.

If you need to change the battery, the settings will also revert

to default settings.

IGI

ALKER

.COM

STEP

DIST

SET

140

JW200

S3-

S1,S2,S4

S3+

Set Step Filter set point

RESETTING YOUR PEDOMETER

Most people prefer to reset counts daily. T o reset your counts:

From STEP or DISTANCE mode, press and hold the yellow

RESET button for at least 2 seconds. Y ou'll see the values all

go back to zero.

CHANGING STEP FILTER SETTING

While the JW200 PedometerEngine™ Step Sensor is

extremely accurate, some people like to have the ability to

filter out false steps. T herefore, the unit has a variable setting

step filter, to allow fine-tuning to your specific preferences.

You can set the value to any value from 0 – 5 steps. For

example, if the filter is set to "3" , the unit will wait to start

counting steps until more than three steps have been taken in

less than five seconds.

Press S3+ (MODE) or S3– (RESET) to change the Step Filter

Setting.

CHANGING UNITS (English vs. Metric)

The Pedometer can display either in English units (in, mi, and lb

- this is the default), or in Metric units (cm, km, and kg). From within

Deep Set mode (see pg. 18), press the S2 button to cycle back and

forth between setting the Step Filter set point and Choice of Unit

System. T he unit will show either "US" or "EU" (for European Union)

depending on the unit system chosen. If you change units after using

the pedometer, the unit will convert all of your data into the new unit

system when you exit Deep Set model. Y ou can check to see which

system of units you are using by seeing which measurement units

are displayed on the Stride and Weight setting screens.

Press S3+ (MODE) or S3– (RESET) to change the Measurement Mode.

Press and hold S4 for 2 seconds to exit Deep Set Mode.

Note: T he unit will save any changes and exit set mode after 30

seconds unattended.

To replace the battery:

1. Insert a coin into the slot on the

bottom of the case, and twist to

loosen the faceplate. Remove

faceplate and set aside.

2. Locate the battery holder as seen

on sketch. Pull out the old battery,

and push a new LR-44 battery into the holder,

with positive terminal (+) facing up.

3. Snap faceplate back into place, hooking the bottom

two tabs first, then closing by pressing together at the

top two tabs.

Battery