Accusplit Alliance 625M8D Інструкція з експлуатації

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Дивись. Accusplit Alliance 625M8D. Accusplit Alliance 625M8D 2 сторінки. Accusplit operating instruction multimodetimer/stop watch 625m8d

Друкувати сторінку

ACCUSPLIT®

ALLIANCE

MULTIMODE TIMER/STOPWATCH

OPERATING INSTRUCTIONS

RESET/SPLIT

ROTARY

SWITCH

INTRODUCTION

This unit has five modes: Stopwatch, Auto Repeat Countdown

Timer, Dual Display Countdown Timer, Pacer, and Preset

Countdown Timer.

Press C (MODE) to change between modes. Note: Timing must

be stopped and reset to zero to change modes.

MEMORY STOPWATCH

SPLIT TIMING

1. Press C to move the cursor to point to

2. Press A to start stopwatch

3. Press B repeatedly to remember the last 8 splits

• Lower display shows cumulative split and upper

display shows lap split

• After 5 seconds, the unit will unlock splits to display

current running split time

4. Press E to recall the last 8 splits

5. Press A to stop counting

6. Press B to reset to zero

START-STOP TIMING

1. Press C to move the cursor to point to

2. Press A to start counting

3. Press A repeatedly to remember the last 8 time-cuts

4. Press E to recall the last 8 times-outs

5. Press A to stop counting

6. Press B to reset to zero

AUTO REPEAT COUNTDOWN TIMER

1. Press C to move the cursor to point to

2. Press D to enter set mode

• Press B to set hours, E to set minutes, A to set seconds

• Press A & B at the same time to reset digits to zero

™

RECALL

UP/DOWN

START/STOP

MODE

SET

AUTO

625M8D

3. Press A to start countdown timing

4. Press E to show the time from start ( )

5. Press E again to return to countdown timing ( )

6. Press A again to stop counting

7. Press B to return to the original setting

8. When time is up, the unit will beep once, then start

counting again. The number of cycles completed is

recorded in brackets in upper left of display.

DUAL DISPLAY COUNTDOWN TIMER

1. Press C to move the cursor to point to

2. Press E to change the dual display timer mode (SU

or Id or UP)

3. Press D to adjust the timer on the lower display

Press D again to adjust the timer on the upper display

• Press B to set hours, E to set minutes, A to set seconds

• Press A & B at the same time to reset digits to zero

• Press D again to complete the settings

4. SU - Two countdown timers work simultaneously

• Press A to start

• Press A to stop (STOP: flashes)

• Press B to reset to the original settings

Id - Two countdown timers work independently

• Press A to start/stop lower display

• Press B to start/stop upper display

• Press A & B at the same time to reset to the original

settings

UP - Two count up timers work independently

• Press A to start/stop lower display (STOP: flashes

when stopped)

• Press B to start/stop upper display (STOP: flashes

when stopped)

• Press A & B at the same time to reset to zero

PACER WITH COUNT UP TIMER

1. Press C to move the cursor to point to

2. Press D to adjust the frequency

• Press A to increase the digits

• Press B to decrease the digits

3. Press A to start pacer

4. Press A again to the stop

5. Press B to reset to zero

6. Press E to turn the pacer's beep ON or OFF

and the symbol (((•))) will appear or disappear

7. Upper display shows count up timer

16 PRESET COUNTDOWN TIMER

1. Press C to move the cursor to point to (1-60)

2. Turn the rotary switch to the desired minutes (1-60)

3. Press A to start countdown timing

4. Press A again to stop countdown timing

5. Alarm Sounds

6. Press B to return to the original setting

To Show Count Up Timing

1. When the time is not up.

a. Press E to check elapsed time ( )

b. Press E again to return to countdown ( )

2. When the time is over,

a. Press E to check the time from start ( flashes)

b. Press E again to show overtime ( flashes)

DUAL

PACE