Cisco ASR 900 Series Посібник з конфігурації - Сторінка 4
Переглянути онлайн або завантажити pdf Посібник з конфігурації для Перемикач Cisco ASR 900 Series. Cisco ASR 900 Series 6 сторінок. Configuring 1g traffic on 8-port 10 gigabit
ethernet interface module
Також для Cisco ASR 900 Series: Посібник з конфігурації (13 сторінок), Посібник з конфігурації (19 сторінок), Посібник з конфігурації (6 сторінок)
Друкувати сторінку
Associated Commands
Router#
TenGigabitEthernet0/4/0 is up, line protocol is up
Hardware is A900-IMA8Z, address is c8f9.f98d.2024 (bia c8f9.f98d.2024)
Internet address is 50.0.0.1/8
MTU 1500 bytes, BW 10000000 Kbit/sec, DLY 10 usec,
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full Duplex, 10000Mbps, link type is auto, media type is SX
output flow-control is off, input flow-control is off
Transport mode LAN
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:08:24, output 00:08:24, output hang never
Last clearing of "show interface" counters 00:07:59
Input queue: 0/375/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
.....
Note
For 10G mode, the hw-module subslot 0/x ether-mode 10G command is not displayed when you use show
running-config command.
To verify the bandwidth and port speed, use the show platform hardware pp active interface all in privileged
EXEC mode:
Router#show platform hardware pp active interface all
bd_id: 0, encap: 1, ip_mtu: 1500, l2_max_tu: 1500, l2_min_tu: 0
vrfid: 8, enctype: 0, admin_state: 1, admin_state_oir: 0
Name: TenGigabitEthernet0/4/6, Asic: 0, hwidx: 10
lpn: 0, ppn: 10, gid: 10, mac: c8f9.f98d.202a
InLportId: 0, ELportId: 0, dpidx: 30, l3ID: 24
port_flags: 0, port_speed: 10000 Mbps, efp_count: 0, destIndex: 10, intType: 1
etherchnl: 0, efp: 0, bdi: 0, l2PhyIf: 0, l3PhyIf: 1, l3TDM: 0, loopBack: 0
tunnel: 0, tunneltp: 0, icmp_flags: 0, icmp6_flags: 0
bandwidth: 10000000, fcid: 0, cid: 0, mpls_tbid: 0, protocols: 4
v4_netsmask: 8, v4_tableid: 6, v6_tableid: 65535, vrf_tbid_dstrm: , snmp_index: 0
bd_id: 0, encap: 1, ip_mtu: 1500, l2_max_tu: 1500, l2_min_tu: 0
vrfid: 6, enctype: 0, admin_state: 1, admin_state_oir: 0
Associated Commands
The following commands are used to configure 8-port 10 Gigabit Ethernet Interface Module (8X10GE):
Configuring 1G Traffic on 8-port 10 Gigabit Ethernet Interface Module
4
show interface
tengigabitethernet0/4/0
reliability 255/255, txload 1/255, rxload 1/255
Interface manager platform keys
-------------------------------------------------
Name: TenGigabitEthernet0/4/7, Asic: 0, hwidx: 9
lpn: 0, ppn: 9, gid: 9, mac: c8f9.f98d.202b
InLportId: 0, ELportId: 0, dpidx: 31, l3ID: 25
port_flags: 0, port_speed: 10000 Mbps, efp_count: 0, destIndex: 9, intType: 1
etherchnl: 0, efp: 0, bdi: 0, l2PhyIf: 0, l3PhyIf: 1, l3TDM: 0, loopBack: 0
tunnel: 0, tunneltp: 0, icmp_flags: 0, icmp6_flags: 0
bandwidth: 10000000, fcid: 0, cid: 0, mpls_tbid: 0, protocols: 4
v4_netsmask: 8, v4_tableid: 8, v6_tableid: 65535, vrf_tbid_dstrm: , snmp_index: 0
Configuring 1G Traffic on 8-port 10 Gigabit Ethernet Interface Module