Sharp CD-DH950P Посібник з експлуатації - Сторінка 7
Переглянути онлайн або завантажити pdf Посібник з експлуатації для Стереосистема Sharp CD-DH950P. Sharp CD-DH950P 17 сторінок. Sharp stereo system user manual
Також для Sharp CD-DH950P: (іспанською) Manual De Usuario (17 сторінок)
Друкувати сторінку
Listening to the iPod or iPhone
iPhone and iPod operations
Made for:
iPhone 4
iPhone 3GS
iPhone 3G
iPhone
iPod touch (4
th
generation)
iPod touch (3
rd
generation)
iPod touch (2
nd
generation)
Caution:
Please update your iPod unit to the latest software version
from Apple's homepage before using it.
Notes:
Once the iPod or iPhone is connected to the unit it will
begin charging.
The iPod or iPhone unit cannot be charged during USB
mode.
The message "This accessory is not made to work with
iPhone" or similar, may appear on the iPhone screen
when:
- battery is low.
- the iPhone is not properly docked (eg. slanting).
If this occurs, remove and re-dock the iPhone.
This product is made for iPhone. To prevent random
interference when iPhone is docked, the headphone
output is disabled, and "HP INVALID" will be displayed.
You may also experience brief audio interference during
incoming calls.
iPod and iPhone adaptor connection
Notes:
Please use the adaptor supplied with your iPod or
iPhone unit.
You can use an audio cable to connect your iPod to the
AUDIO IN jack if:
1.
your iPod adaptor does not fi t into the iPod dock on
the main unit.
2.
you have an iPod that does not have an iPod
adaptor.
3.
you have an iPod that does not have an iPod 30 pin
connector.
iPhone
iPhone
Adaptor No.
Description
12
iPhone
15
iPhone 3G
15
iPhone 3GS
19
iPhone 4
To insert iPod or iPhone adaptor
Insert the iPod or iPhone adaptor into the unit and connect
your iPod or iPhone.
iPhone dock
iPhone
iPhone (bottom)
Dock connector
st
iPod touch (1
generation)
iPod classic
th
iPod nano (6
generation)
th
iPod nano (5
generation)
iPod nano (4
th
generation)
iPod nano (3
rd
generation)
iPod nano (2
nd
generation)
Capacity
4GB & 8GB & 16GB
8GB & 16GB
16GB & 32GB
16GB & 32GB
iPhone
adaptor
iPhone
connector
To remove iPod or iPhone adaptor
Insert the tip of a screwdriver ("-" type, small)
into the adaptor hole as shown and lift upward
to remove.
iPod or iPhone playback
1
Press the ON/STAND-BY button to turn the power on.
2
Press the iPod/iPhone button to select iPod or iPhone
function.
3
Insert iPod or iPhone unit in iPod or iPhone dock of
main unit. "DOCK OK" will be displayed.
4
Press the
playback.
Note:
iPod and iPhone cannot be played back via USB cable and
connection, "NO SUPPORT" will be displayed.
iPhone playback
Sound will only switch from iPhone to the main unit after
authentication process is completed in approximately
10 seconds.
Incoming calls will pause the playback.
Once the calls are answered, the conversation can
only be heard through the built-in iPhone speaker. Turn
on the iPhone speaker or undock the iPhone to start
conversation.
To disconnect iPod or iPhone
Simply remove the iPod or iPhone from the iPod or iPhone
dock. It is safe to do so even during playback.
Navigating the iPod or iPhone menus
1
Press the MENU button to view the menu on iPod
or iPhone unit. Press it again to go back to previous
menu.
2
Use the PRESET (
the menu and then press ENTER button.
Note:
When navigating the iPod or iPhone menu with remote
control, do not operate any of the buttons on the iPod or
iPhone unit. The volume level is adjusted by turning the
volume knob on main unit or pressing the VOL (+ or –)
button on the remote control. Adjusting the volume on the
iPod unit gives no effect.
iPod or iPhone operation
The operations described below depend on the generation
iPod or iPhone you are using.
System on operation
When the main unit is powered on, the iPod or iPhone
unit will automatically power on when docked in the unit
(including TIMER function).
System off (stand-by operation)
When the main unit is turned to stand-by mode, the
docked iPod or iPhone unit will automatically turn to stand-
by mode.
E-6
(iPod or iPhone
) button to start
or
) button to select an item on