Sharp PGF267X - XGA DLP Projector Посібник з налаштування - Сторінка 22
Переглянути онлайн або завантажити pdf Посібник з налаштування для Проектор Sharp PGF267X - XGA DLP Projector. Sharp PGF267X - XGA DLP Projector 34 сторінки. (2500 ansi lumens) short-throw brilliantcolor dlp projector
Також для Sharp PGF267X - XGA DLP Projector: Технічна специфікація (2 сторінок)
Друкувати сторінку
Setting up the Projector Using RS-232C or Telnet
SETUP MENU
▼SETUP MENU
-----------------------------SETUP MENU----------------------------
[1]IP Address
[2]Subnet Mask
[4]User Name
[5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup
[V]View All Setting
[S]Save & Quit
setup>
[1] IP Address
IP address settings. (Page 25)
[2] Subnet Mask
Subnet mask settings. (Page 25)
[3] Default Gateway
Default gateway settings. (Page 25)
[4] User Name (Factory default setting: Not
Required)
Setting of user name for security protection.
(Page 25)
[5] Password (Factory default setting: Not
Required)
Setting of password for security protection.
(Page 26)
[6] RS-232C Baud Rate (Factory default setting:
9600 bps)
Baud rate settings for the RS-232C terminals.
(Page 26)
[7] Projector Name
It is possible to assign a projector name. (Page 26)
[8] DHCP Client
DHCP Client settings. (Page 26)
[A] Advanced Setup
Enters ADVANCED SETUP MENU. (Page 27)
[D] Disconnect All
Disconnect all connections. (Page 27)
[V] View All Setting
Displays all setting values. (Page 23)
Can also be used with ADVANCED SETUP
MENU.
[S] Save & Quit
Save set values and quit menu. (Page 24)
[Q] Quit Unchanged
Quit menu without saving setting values. (Page 24)
Note
•
When "DHCP Client" is set to "OFF" on the
projector:
IP address: 192.168.150.2
Subnet mask: 255.255.255.0
Default gateway: 0.0.0.0
-22
(Main Menu)
[3]Default Gateway
[D]Disconnect All
[Q]Quit Unchanged
ADVANCED SETUP MENU
▼ADVANCED SETUP MENU
********************** ADVANCED SETUP MENU ***************************
[1]Auto Logout Time
[2]Data Port
[5]Network Ping Test
[6]Accept IP Addr(1)
[7]Accept IP Addr(2)
[9]Accept All IP Addr
[0]Search Port
[!]Restore Default Setting
[Q]Return to Main Menu
advanced>
[1] Auto Logout Time (Factory default setting:
5 minutes)
Setting of time until automatic disconnection of
network connection. (Page 27)
[2] Data Port (Factory default setting: 10002)
Setting the TCP port number used when
exchanging data. (Page 27)
[5] Network Ping Test
It is possible to confi rm that a network
connection between the projector and a
computer etc. is working normally. (Page 28)
[6] Accept IP Addr(1)
[7] Accept IP Addr(2)
[8] Accept IP Addr(3)
[9] Accept All IP Addr (Factory default setting:
Accept All)
For improved security, it is possible to set up
to three IP addresses allowing connection to
the projector.
Set IP addresses can be cancelled using [9]
Accept All IP Addr. (Page 28)
[0] Search Port (Factory default setting: 5006)
Setting the port number used when searching
for the projector. (Page 29)
[!] Restore Default Setting
Restores all setting values that can be set
using the menu to the default state. (Page 29)
[Q] Return to Main Menu
Return to the main SETUP MENU. (Page 29)
[8]Accept IP Addr(3)