Siemens SIMATIC ET 200SP Посібник - Сторінка 17

Переглянути онлайн або завантажити pdf Посібник для Промислове обладнання Siemens SIMATIC ET 200SP. Siemens SIMATIC ET 200SP 34 сторінки. Distributed i/o system
Також для Siemens SIMATIC ET 200SP: Посібник (40 сторінок), Посібник користувача (21 сторінок), Посібник (34 сторінок), Посібник (48 сторінок), Посібник (30 сторінок), Посібник (34 сторінок), Інформація про продукт (38 сторінок), Посібник (37 сторінок), Посібник (36 сторінок), Посібник (44 сторінок), Посібник (31 сторінок), Посібник (35 сторінок), Посібник (23 сторінок), Посібник з конфігурації (20 сторінок), Посібник (34 сторінок), Посібник (29 сторінок), Посібник (33 сторінок), Посібник (31 сторінок), Посібник користувача (32 сторінок), Посібник (31 сторінок), Посібник (28 сторінок), Посібник (41 сторінок), Посібник (32 сторінок), Посібник (49 сторінок), Посібник (24 сторінок), Посібник (41 сторінок), Посібник (30 сторінок), Посібник (31 сторінок), Посібник (27 сторінок), Посібник (24 сторінок), Посібник (24 сторінок), Посібник (25 сторінок), Посібник (49 сторінок), Посібник (40 сторінок), Посібник (38 сторінок), Посібник (39 сторінок), Інформація про продукт (24 сторінок), Посібник (32 сторінок), Інформація про продукт (10 сторінок), Посібник з експлуатації обладнання (43 сторінок), Посібник (33 сторінок), Посібник з експлуатації обладнання (44 сторінок), Оригінальна інструкція з експлуатації (6 сторінок), Посібник (35 сторінок), Посібник (28 сторінок), Посібник з експлуатації обладнання (32 сторінок), Посібник (50 сторінок), Посібник (30 сторінок), Посібник (26 сторінок), Посібник (28 сторінок), Посібник (34 сторінок), Посібник (44 сторінок), Посібник (33 сторінок), Посібник з експлуатації обладнання (42 сторінок), Оригінальна інструкція з експлуатації (16 сторінок)

Siemens SIMATIC ET 200SP Посібник
Parameters
Reaction to CPU STOP •
Potential group
Due to the limited number of parameters at a maximum of 244 bytes per ET 200SP station with a PROFIBUS GSD
1
configuration, the configuration options are restricted. If required, you can assign these parameters using data rec-
ord 128 as described in the "GSD file PROFINET IO" column (see table above). The parameter length of the I/O module
is 32 bytes.
Note
• If both parameters "Diagnostics: short-circuit to L+" and "Diagnostics: wire break" are
enabled and one of these diagnostic events occurs, the affected channel is switched off.
This prevents undefined load switching and the corresponding diagnostic alarm is
triggered.
• If both parameters "Diagnostics: short-circuit to L+" and "Diagnostics: wire break" are
enabled and one of these diagnostic events occurs, the affected channel is switched off.
This prevents undefined load switching and the corresponding diagnostic alarm is
triggered.
• If the parameter "Diagnostics: short-circuit to L+" is enabled and "Diagnostics: wire break"
is disabled, the signal status is retained at the affected channel when "Diagnostics: short-
circuit to L+" occurs. A diagnostic alarm is triggered only for 0 signal.
Digital output module DQ 16x24VDC/0.5A ST (6ES7132-6BH01-0BA0)
Manual, 09/2017, A5E03574420-AE
Range of values
Turn off
Keep last value
Output substitute
value 1
Use potential group of
the left module (mod-
ule plugged into a
dark-colored Ba-
seUnit)
Enable new potential
group (module
plugged into light-
colored BaseUnit)
Default
Parameter
reassign-
ment in
RUN
Turn off
Yes
Use potential
No
group of the left
module
Parameters/address space
4.1 Parameters
Scope with configuration software,
e.g. STEP 7 (TIA Portal)
GSD file
GSD file
PROFINET IO
PROFIBUS DP
Channel
Module
Module
Module
1
17