Cisco Cisco Access Registrar 4.2 Посібник для початківців - Сторінка 26

Переглянути онлайн або завантажити pdf Посібник для початківців для IP-телефон Cisco Cisco Access Registrar 4.2. Cisco Cisco Access Registrar 4.2 46 сторінок. Telepresence conference system
Також для Cisco Cisco Access Registrar 4.2: Налаштування мережевих параметрів (34 сторінок), Посібник користувача (44 сторінок)

Друкувати сторінку

Cisco Cisco Access Registrar 4.2 Посібник для початківців

Cisco TelePresence Video Systems

Contents

Configuring H.323 and SIP

(When not set by a provisioning system)

To get online and ready to place and receive calls, your system

must be set up properly. Your system uses either the H.323

protocol or the SIP protocol for video calls.

NOTE:

Contact your system administrator, or service provider,

for information about the network settings.

For networks administered through Cisco TMS (Cisco

TelePresence Management Suite), your Cisco TMS adminis-

trator will help you to get online.

You can find information about administering through Cisco UCM

in the

Administering TC endpoints on CUCM

The diagnostics on your system will indicate if there is a problem

with the H.323 or SIP registering.

NOTE:

H.323. is not available for the SX10.

If you are changing a value setting,

you have to always click

save

to confirm the change.

Back to task overview

D14639.15 Video Systems Getting Started Guide TC7.2, OCTOBER 2014.

Introduction

User interfaces

H.323

If in doubt for any of the parameters below, contact your system

administrator or your service provider.

1. Go to the

Configuration

2. Open the

3. Under

Profile1

the

E164

and the

4. Go to the

If you want the system to obtain the H.323 gatekeeper

guide.

address automatically, select

down list; if you want to enter the address manually, select

Manual.

If set to Manual, enter the gatekeeper

sponding input field.

5. If the H.323 gatekeeper requires authentication, and you

want your system to authenticate itself to the gatekeeper, go

to the

Authentication

drop down list. Then enter the

the corresponding input fields.

Otherwise, select

6. Click the

Home

the H.323 settings.

If you have successfully registered to a Gatekeeper, the

Status

is shown as

If you wish to change the other H.323 settings, check the admin-

istrator guide for your product.

Configuration

tab, and select

System

Configuration.

H323

settings from the left sidebar.

heading and the

H323Alias

subheading, enter

number in their respective input fields.

Gatekeeper

subheading.

Auto

in the

Discovery

Address

in the corre-

subheading and select

in the

LoginName

and

Password

Off

in the

Mode

drop down list.

tab to see the

System Information

and verify

Registered

in the H323 section.

Appendices

SIP

If in doubt for any of the parameters below, contact your system

administrator or your service provider.

1. Go to the

Configuration

tab, and select

2. Open the

SIP

page from the left sidebar.

3. Under the

Profile 1

heading, enter the SIP URI in the

input field, and optionally a display name in the

input field.

Select the preferred transpor t protocol from the

DefaultTransport

drop down list. If you select Auto, the

drop

system first tries to connect using Tls, then TCP, and finally

UDP.

4. Select a proxy type in the

type is Standard.

5. Go to the

Proxy 1

subheading.

If you want the system to obtain the SIP proxy address

Mode

automatically, select

Auto

if you want to enter the address manually, select Manual.

If you select Manual, enter the proxy

sponding input field.

6. If the SIP proxy requires authentication, you must enter a

to the

Authentication 1

subheading and enter the

and

Password

in the corresponding input fields.

7. Click the

Home

tab to see the

the SIP settings.

If you have successfully registered to a SIP server, the

Status

is shown as

Registered

If you wish to change the other SIP settings, check the admin-

istrator guide for your product.

Getting Started Guide

Contacts

System

Configuration.

URI

DisplayName

Type

drop down list. The default

in the

Discovery

drop down list;

Address

in the corre-

LoginName

System Information

and verify

in the SIP section.