Ricoh Aficio CL5000 Посібник зі швидкого встановлення - Сторінка 4
Переглянути онлайн або завантажити pdf Посібник зі швидкого встановлення для Принтер Ricoh Aficio CL5000. Ricoh Aficio CL5000 4 сторінки. Ricoh cl5000 laser printer quick installation guide
Також для Ricoh Aficio CL5000: Інструкція по застосуванню (2 сторінок), Посібник зі швидкого встановлення (4 сторінок), Додатковий посібник (3 сторінок), Посібник (12 сторінок)
Друкувати сторінку
CONFIGURING THE PRINTER
FOR THE NETWORK
Connecting the printer to a computer using a parallel cable.
You must configure the printer setting using the
Important
control panel when using in a network environment.
The parallel cable is not provided with the printer.
The following list is the items you can set and their
It is your responsibility to provide the parallel cable
default settings.
appropriate for the computer that you are using.
The printer's parallel connection is a standard bi-
directional interface. It requires a standard 36-pin
IP Address
parallel cable compliant with IEEE1284 and the
parallel port on the computer.
Subnet Mask
To avoid electrical interference, use a shielded cable.
Gateway Address
Note
Network Boot
Do not use a parallel cable longer than 2.5 meters (8.2 feet).
Frame Type (NW)
Confirm that the printer's power switch is off. If it
Active Protocol
is on, turn it off.
Ethernet
Turn the computer off.
The procedure below shows how to set the TCP/IP
protocol. Make the settings for the other items by
taking the same procedure.
Attach the parallel cable to the port of the
Press {Menu}.
printer. Secure the cable with the metal fittings
as shown in the illustration.
"Menu" appears on the panel display.
Important
Menu:
Paper Input
Rating voltage of the parallel port for the computer;
Max. DC 5V.
Press { } or { } to display "Host Interface",
and then press {Enter #}.
Menu:
Host Interface
The interface setiing menu appears.
Start the protocol for use.
ZESX339E
Attach the other end of the parallel cable to the
port of the computer. Secure the cable.
Press { } or { } to display "Network
Setup", and then press {Enter #}.
Turn on the printer and the computer.
Host Interface:
Network Setup
Go to
"INSTALLING THE PRINTER
Press { } or { } to display "Active
DRIVER".
Protocol", and then press {Enter #}.
Network Setup:
Active Protocol
Connecting the printer to a computer using a USB cable.
Press { } or { } to display "TCP/IP", and
Important
then press {Enter #}.
The USB interface cable is not provided with the
printer. Make sure that the USB interface cable you
use, is appropriate for your computer.
Active Protocol:
TCP/IP
Attach the USB interface cable to the USB interface
connector of the printer. Secure the cable.
ZESXK500E
Attach the other end of the interface cable to the
USB interface connector of the computer or the
USB Hub. Secure the cable.
Press { } or { } to display "Active", and
then press {Enter #}.
TCP/IP:
*Active
Note
011.022.033.044
* shows the current setting.
000.000.000.000
In about two seconds, the display returns to the "Active Protocol"
000.000.000.000
setting screen.
None
Set the rest of the protocols for use.
Auto
When all settings for the protocol are done,
TCP/IP
press {Escape}.
Auto
The "Network Setup" setting screen appears.
Note
The default settings for all of the protocols are
"Active".
It is recomended to set the unused protocols "Not
Active".
Set the IP address for the printer.
Note
Confirm the IP address to the network
administrator.
Press { } or { } to display "IP Address",
and then press {Enter #}.
Network Setup:
IP Address
The currently selected IP address appears.
Note
When {Enter #} is pressed, the cursor moves to the
next field.
When { } or { } is kept pressed for a few
seconds, the value chages by 10.
Press { } or { } to set the value for the
field.
IP Address:
199.022.033.044
Press {Enter #}.
The cursor moves to the next field.
Repeat
and
to set the value for the
rest of the fields.
Set "Subnet Mask" and "Gateway Address" by
following the same procedure for setting the IP
address.
Important
The subnet mask is the mask value to use a part of
the IP address as a network address. Confirm the
value to the network administrator.
The gateway address is the address of the host or
router that acts as a gateway when interacting with
work stations in another network. Confirm the value
to the network administrator.
Note
If you are not sure of the setting addresses, leave
them as default.
When using the DHCP with TCP/IP protocol, set
Insert the CD-ROM labeled "Printer Drivers and
the network boot.
Utilities" into the CD-ROM drive.
Auto Run will start the installer.
Press { } or { } to display "Network
Boot", and then press {Enter #}.
Select a language to change the interface
language, and then click [OK].
Network Setup:
The following languages are available:
Network Boot
Cestina (Czech), Dansk (Danish), Deutsch (German), English
(English), Espanol (Spanish), Francais (French), Italiano (Italian),
Press { } or { } to display "DHCP", and
Magyar (Hungarian), Nederlands (Dutch), Norsk (Norwegian),
then press {Enter #}.
Polski (Polish), Portugues (Portuguese), Suomi (Finnish), Svenska
(Swedish)
Network Boot:
Default interface language is English.
*DHCP
Note
* shows the current setting.
In about two seconds, the display returns to the "Network
Setup" setting screen.
When all of the settings are done, press
{On Line}.
"Ready" appears on the panel display.
Ready
Select [Quick Install].
The software license agreement appears in the [License Agreement]
dialog box.
Print the configuration page to confirm the
settings made.
See
"PRINTING THE TEST PAGE" for printing the configuration
page.
This is an example when English is selected in step
After reading through all of the contents, click [I
INSTALLING THE PRINTER
accept the agreement] to agree with the License
Agreement, and then click [Next].
DRIVER
You can install the printer drivers and software
easily from the CD-ROM labeled "Printer Drivers
and Utilities".
Click [Quick Install] in the window of the CD-ROM
to install PCL5c and RPCS printer drivers. To install
the PostScript 3 printer driver, click the PostScript
3 printer driver button. For more information about
the PostScript 3 printer driver, see the Administrator
Reference or the Client Reference on the CD-ROM
labeled "Operating Instructions" depending on the
environment you use in.
Select the printer model you want to install in the
When the TCP/IP protocol is used, SmartNet-
"Select Printer" dialog box.
Monitor for Client will be installed as well.
The supported operating systems are Windows 95/
98/Me, Windows 2000, Windows XP, and Windows
NT 4.0.
When using with TCP/IP protocol, confirm the followings:
The printer is connected to a network with
the ethernet cable.
The TCP/IP protocol is set.
The IP address is set for the printer and the
computer.
Note
For a network connection with TCP/IP, select the
printer whose IP address is displayed in [Connect
to].
For parallel connection, select the printer whose
printer port is displayed in [Connect to].
Click [Install].
The following display appears while installing the printer driver.
When finished, the [Installation Completion] dialog box appears.
Note
With Windows 2000, the [Digital Signature Not
Found] dialog box may appear when installing the
printer driver. In this case, click [Yes] to continue
the installation.
Click [Finish].
Note
.
A message directing to restart the computer may
appear. In this case, restart your computer to
complete the installation. When no such message
appears, go to step
.
Click [Exit].
The installation is now complete.
Copyright© 2001 G071-7503A
Printed in China
UE USA