Epson EMP-715 - XGA LCD Projector Інформація про продукт - Сторінка 6
Переглянути онлайн або завантажити pdf Інформація про продукт для Проектор Epson EMP-715 - XGA LCD Projector. Epson EMP-715 - XGA LCD Projector 13 сторінок. Epson powerlite 505c: product information
Також для Epson EMP-715 - XGA LCD Projector: Технічні характеристики (3 сторінок)
Друкувати сторінкуEPSON PowerLite 505c/715c Projector
Shutting Down the Projector
When you've finished using the projector, follow the
recommended procedure to shut it down. This extends the life
of the lamp and protects the projector from possible
overheating.
Note: When the projector has not received any input signals for
30 minutes, it automatically turns off the lamp and enters "sleep
mode." This conserves electricity, cools the projector, and extends
the life of the lamp. If you are done using the projector, unplug the
power cord. If you want to start projecting again, press the
button.
1. If you're using a computer, shut it down first.
2. To turn off the projector, press the red
projector or remote control. You see a confirmation message.
(If you don't want to turn it off, press any other button.)
Power
3. Press the
button again. The power light flashes
orange for about a minute as the projector cools down.
When the projector has cooled, the orange light stays on and
the exhaust fan shuts off.
If you want to turn the projector on again, wait until the
orange light stops flashing. Then press the
Caution: To avoid damaging the projector or lamp, never
unplug the power cord when the power light is green or
flashing orange.
4. Replace the lens cap, retract the lens, and unplug the power
cord.
5. If you're using a VCR or other video source, turn it off after
you turn off the projector.
6. Disconnect all equipment, and store the projector in the bag
that came with it or in a protective case.
EPSON PowerLite 505c/715c Projector
6 -
Power
Power
button on the
Power
button.
1/01
Projector Status Lights
The lights on top of the projector indicate the projector's
status and let you know when a problem occurs.
Light
Status
Description and action
orange
The projector is in sleep mode. You can unplug
it or press the Power button to turn it on.
flashing
The projector is warming up. Wait for the image
green
to appear.
green
The projector is operating normally.
flashing
The projector is cooling down. You can't turn
orange
the projector on (and should not unplug it) until
the light stops flashing and remains orange.
flashing
Power is cut off because of an internal
red
problem. Remove the power cord and contact
EPSON for help.
red
The lamp is burned out. Replace it as
described on page 10.
flashing
The lamp is almost burned out. This is a good
orange
time to replace it, following the instructions on
page 10.
flashing
There is a problem with the lamp, power
red
supply, fuse, or circuit. If necessary, replace
the lamp as described on page 10.
flashing
The projector is in a high-temperature cooling
orange
cycle. Make sure the temperature surrounding
the projector does not exceed 104
is plenty of space around and under the
projector for ventilation. Clean the air filter if
necessary. See page 9 for instructions.
red
The projector has turned off automatically
because it has overheated. Let it cool for a few
minutes, then turn it back on. Make sure
nothing is blocking the vents on the front and
top of the projector. If it continues to overheat,
you may need to change the air filter. See
page 9 for instructions.
flashing
There is a problem with the cooling fan or
red
temperature sensor. Turn off the projector and
unplug it. Contact EPSON for help.
power light
lamp light
temperature
light
°
F and there