Cisco AIR-LAP1310G-A-K9 Технічний паспорт - Сторінка 9
Переглянути онлайн або завантажити pdf Технічний паспорт для Бездротова точка доступу Cisco AIR-LAP1310G-A-K9. Cisco AIR-LAP1310G-A-K9 15 сторінок. Outdoor access point or bridge
Друкувати сторінку
Protocols
Nonoverlapping
Channels
Security—Bridge
Role*
Security—Access
Point Role
Security—
Workgroup Bridge
Role*
SNMP Compliance
* Cisco Aironet 1300 Series can operate as a workgroup bridge or wireless bridge when it is an autonomous device. When the
Cisco Aironet 1300 Series is operating under the Cisco Unified Wireless Network architecture, it only operates as an access point.
Components
Table 3 lists the components available for the Cisco Aironet 1300 Series.
Table 3.
Components
Power Injector LR2
Power Injector LR2T
Power Supply
AIR-BR1310G- x-K9
or AIR LAP1310G-x-
K9 Integrated
Antenna
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Description
3
Cisco Wireless Security Suite, including:
Authentication
802.1X support including LEAP to yield mutual authentication and dynamic per-user, per session encryption keys
Encryption
● Cisco TKIP or WPA TKIP; key hashing (per-packet keying), Message Integrity Check (MIC) and broadcast key rotation
● AES (802.11i)
Cisco Wireless Security Suite supporting WPA and WPA2, including:
Authentication
● Management frame protection provides for the authentication of 802.11 management frames by the wireless network
infrastructure. This allows the network to detect spoofed frames from access points or malicious users impersonating
infrastructure access points. If an access point detects a malicious attack, an incident will be generated by the access
points and reports will be gathered on the Cisco wireless LAN controller, Cisco WCS, or CiscoWorks WLSE.
● 802.1X support including Cisco LEAP, Protected EAP-Generic Token Card (PEAP-GTC), PEAP-Microsoft Challenge
Authentication Protocol Version 2 (MSCHAPv2), EAP Message Digest 5 (EAP MD5), EAP-Transport Layer Security (EAP-
TLS), EAP-Tunneled TLS (EAP-TTLS), EAP-Subscriber Identity Module (EAP-SIM), and EAP-Flexible Authentication via
Secure Tunneling (EAP-FAST) to yield mutual authentication and dynamic per user, per-session encryption keys
Encryption
● WPA: Cisco TKIP or WPA TKIP; key hashing (per-packet keying), MIC and broadcast key rotation
● WPA2: AES (802.11i)
Cisco Wireless Security Suite, including:
Authentication
● 802.1X support including Cisco LEAP to yield mutual authentication and dynamic per-user, per session encryption keys
Encryption
● Cisco TKIP or WPA TKIP; key hashing (per-packet keying), MIC and broadcast key rotation
● AES (802.11i)
Versions 1 and 2
Components
Description
The power injector converts the standard 10/100BASE-T Ethernet Cat5 RJ-45 interface that is suitable for weather-protected
areas to a dual F-Type connector interface for dual coaxial cables that are more suitable for harsh outdoor environments.
While providing a 100BASE-T interface to the Cisco Aironet 1300 Series, the power injector also provides power to the unit
over the same cables with a power discovery feature that protects other appliances from damage should they accidentally be
connected. As an added benefit to the installer, the automatic medium-dependent interface crossover (Auto-MDIX) feature is
built in, allowing the dual cables to be swapped while maintaining the same capability. To support longer cable runs from your
network switch or router, the power injector is designed to accommodate up to a 100 meter coaxial cable run plus 100 meters
of indoor Cat5 cable—enabling total cable runs up to 200 meters. Lightning and surge protection is also included at the F-
Type connector interface to provide added protection to your network devices. The power injector requires a 48V DC source
supplied by Cisco.
The Power Injector LR2T supports all the capabilities of LR2. It is designed for use in transportation applications and operates
with an input voltage range of +12 to +40V DC. The DC source is provided by the user. The LR2T can therefore be vehicle- or
solar-powered.
● 48V DC supply for AIR-PWRINJ-BLR2=
● User-supplied 12 to 40V DC source for AIR-PWRINJ_BLR2T=. Could require an external load-dump-module for
automotive and bus installations.
● Vertical polarization
● 13-dBi gain
● 36° E-plane by 38° H-plane (3-dB beam width)
Data Sheet
Page 9 of 14