CABASSE SANTORIN 21 Посібник - Сторінка 8

Переглянути онлайн або завантажити pdf Посібник для Сабвуфер CABASSE SANTORIN 21. CABASSE SANTORIN 21 14 сторінок.
Також для CABASSE SANTORIN 21: Брошура (2 сторінок), Брошура (2 сторінок), Брошура (7 сторінок), Посібник (17 сторінок), Посібник (17 сторінок), Інструкція з експлуатації Посібник з експлуатації (14 сторінок)

Друкувати сторінку

e n g l i s h

Interconnections

with the CINCH RCA connectors

Connections to the LINE IN

If your preamplifier or your integrated amplifier is fitted with a

stereo low-level output, then connect its L (left) and R (right) out-

puts to the L (left) and R (right) LINE IN

woofer.

If your amplifier offers a one mono output, connect it to either

the L (left) or the R (right) subwoofer LINE IN

Connections from the LINE OUT

The signal from the L (left) and R (right) LINE OUT

the one being brought in by the L (left) and R (right) LINE IN

connectors filtered at 80 Hz.

These outputs can thus be used to bring the signal to the ampli-

fier powering the main loudspeaker.

Interconnections with the speaker terminals

Connections to the HI LEVEL INPUT

If the preamp section of your Hi-Fi or audio-video system is not

fitted with a lowlevel output, you should then connect the sub-

woofer by using its loudspeaker terminals. When connecting

the L (left) and R (right) speaker outputs of your amplifier to the

HI LEVEL INPUT

plugs of the subwoofer, be careful not to

cross (-) and (+) cord of either L (left) or R (right) channel. Such

a phase inversion might damage your main amplifier.

Connections from the HI LEVEL OUTPUT

These outputs can be used to bring the signal to the main loud-

speaker systems or to a second subwoofer in a parallel mono

configuration. In the last lay-out, the L (left) and R (right) HI

LEVEL OUTPUT

terminals must be connected to the L (left)

and R (right) HI LEVEL INPUT

fer. The input signal must then arrive into the first subwoofer by

its L (left) and R (right) HI LEVEL INPUT

The signal from the L (left) and R (right) HI LEVEL OUTPUT

plugs, filtered at 200 Hz is the one being brought in by the

HI LEVEL INPUT

connectors.

These outputs can thus be used to bring the signal to the main

loudspeaker systems.

Power supply

The AC IN

cord must be connected to the mains to supply

the subwoofer. The selection of the right voltage 115 V - 230 V

is done with the selector 150 V - 230 V

on AUTO or ON.

With the switch on the AUTO position, the unit will mute after

a few minutes without input signal. The system turns on auto-

matically when signal comes back.

Attention, before operating the unit, be sure that the operating

voltage of your unit is identical with that of your local power vol-

tage.

ADJUSTMENTS

LEVEL

For a first volume adjustment, position the CROSSOVER FRE-

QUENCY

at around 120 Hz, and turn slowly the volume

LEVEL

clockwise from minimum level up to a position whe-

re you feel that the subwoofer sound level is appropriate. A

check of the level adjustment will be necessary after following

steps.

connectors

inputs of the sub-

inputs.

connectors

plugs is

plugs

ones of the second subwoo-

terminals.

. Switch POWER

CROSSOVER FREQUENCY

This potentiometer adjusts the cut-off frequency which determines

the working bandwidth of the subwoofer. This adjustment should

be done according to the specifications of the main speakers and

the room acoustics. Choose the best frequency after various lis-

tening tests.

PHASE

For a better sound integration of the subwoofer in the main sys-

tem, the PHASE

of the subwoofer might have to be inver-

ted (180° position), depending on the distance between the sub-

woofer and the main speakers. You have to check the PHASE

each time you move your speakers and each time you adjust the

CROSSOVER FREQUENCY

woofers, both phase switches must be on the same position.

SPECIFICATIONS & TECHNICAL DATA

Santorin 21

Band pass active subwoofer

Drive unit: ø 21 cm (8 in) - type 21MT3

Frequency bandwidth:

35-160 Hz in semi-reverberating chamber

Maximum RMS SPL: 108 dB

Maximum output power: 250 W

Peak power: 750 W

Lowpass cut-off frequency: 40 to 160 Hz

Phase switch: 0° normal - 180° reverse

Input: 2 low level - 2 high level

Voltage: 115 / 230 V AC - 50 / 60 Hz

Maximum power consumption: 165 W

Dimensions (h x w x d): 33 x 33 x 36 cm - 13 x 13 x 14 in

Weight: 13 kg - 29 lb

Santorin 25

Active subwoofer

Drive unit: ø 25 cm (10 in) - type 25S20

Frequency bandwidth:

34-150 Hz in semi-reverberating chamber

Maximum RMS SPL: 111 dB

Maximum output power: 250 W

Peak power: 750 W

Lowpass cut-off frequency: 40 to 150 Hz

Phase switch: 0° normal - 180° reverse

Input: 2 low level - 2 high level

Voltage: 115 / 230 V AC - 50 / 60 Hz

Maximum power consumption: 165 W

Dimensions (h x w x d): 42 X 36 X 38 cm - 16.5 x 14 x 15 in

Weight: 18 kg - 39 lb

Because of technical improvements already under way in our

constant search for optimum quality, Cabasse reserves the right

to modify all the models presented in specification sheets, adver-

tising materials and manuals without prior notice.

Our web site www.cabasse.com will give you the specific adjust-

ments we recommend for the use of our active subwoofers.

. Attention, if you use 2 sub-