Epson Artisan 1430 Почніть звідси. - Сторінка 3

Переглянути онлайн або завантажити pdf Почніть звідси. для Принтер "Все в одному Epson Artisan 1430. Epson Artisan 1430 4 сторінки. All-in-one printer epson artisan 1430
Також для Epson Artisan 1430: Важливі інструкції з техніки безпеки (12 сторінок), Посібник із стрільбища (7 сторінок), Інструкція з монтажу Посібник з монтажу (7 сторінок)

Друкувати сторінку

Connection options

Wireless connection

You must install the software on every computer from which

you want to print. The installer may prompt you to connect

the printer to your computer with a USB cable temporarily.

After the printer is connected to the network, you will be

prompted to remove the cable. (USB cable not included.)

Make sure you know your network name (SSID) and network

password:

• Network name

• Network password

If you don't have this information, contact the person who set

up your network.

Note:

If you connect to your network using Wi-Fi Protected Setup

(WPS) on Windows, you do not need to know your SSID and network

password.

Direct USB connection

Make sure you have a USB cable.

Any problems?

Network setup was unsuccessful.

• If you're connecting the printer via Wi-Fi Protected Setup

(WPS), make sure you press and hold the Wi-Fi button on

the printer within 2 minutes of pressing the WPS button on

your router. Press and hold the Wi-Fi button on the printer

for 3 seconds.

• Try connecting to the router or access point with your

computer or another device to conﬁ rm that it is working

correctly.

• Try resetting the router (turn it off and then on), then try to

connect to it again.

• Press the

button to print a network status sheet. Verify

that the network settings are correct and check the signal

strength. If it's poor, try moving the printer closer to your

router or access point. Avoid placing the printer next to a

microwave oven, 2.4 GHz cordless phone, or large metal

objects such as a ﬁ ling cabinet.

• If your router or access point doesn't broadcast its network

name (SSID), manually enter the name. If your router or

access point has wireless security enabled, you'll also

need to know what kind of security it's using and make

sure you enter the WEP key or WPA passphrase correctly.

• When using TCP/IP, make sure your network's DHCP

option is enabled (your router manufacturer will be able to

assist you with this setting).

• Disable the ﬁ rewall temporarily to see if that may be

causing the problem. Contact your ﬁ rewall manufacturer

for assistance.

Setup is unable to find my printer after connecting it

with a USB cable.

Make sure it is securely connected as shown:

Printing problems

• Make sure the paper size selected in the printer software

matches the size of paper you loaded.

• Printing stops when an ink cartridge is expended. If a

cartridge is expended, you must replace it to continue

printing.

Paper feeding problems

If paper doesn't feed correctly, remove the paper and fan the

sheets, then reload them. Don't load paper above the tabs on

the edge guides.

Print quality problems

• Make sure your paper is loaded printable side up (usually the

whiter, brighter, or glossy side).

• For the best print quality, use Epson papers and genuine

Epson ink cartridges.

• Make sure the paper type selected in the printer software

matches the paper you loaded. See the online User's Guide

for more information.

• If you notice light or dark bands across your printouts or

they are too faint, run a nozzle check to see if the print

head needs cleaning. See the online User's Guide for more

information.

• If you notice jagged vertical lines, you may need to align the

print head. See the online User's Guide for more information.

• The ink cartridges may be low on ink. Check your cartridge

levels and replace cartridges, if necessary. See the online

User's Guide for more information.

Error indicators

If you see one of the error indicators below, follow the steps

here to proceed:

Off

Flashing slowly

Paper is out, the CD/DVD tray is not inserted correctly

(if printing on a CD or DVD), or multiple sheets have

fed at the same time. Load paper or the CD/DVD tray

correctly and press the

Paper is jammed in the printer, the output tray is closed,

or the CD/DVD tray did not eject (if printing on a CD or

DVD). Remove any jammed paper and make sure the

output tray is open, then press the

resume printing. If printing on a CD or DVD, pull out the

CD/DVD tray and press the

An ink cartridge is not installed, installed incorrectly,

expended, or cannot be used with the printer. Make sure

all ink cartridges are installed correctly and replace any

expended or incompatible ink cartridges.

An ink cartridge is nearly expended. You can continue to

use it until it is expended.

The print head is obstructed by jammed paper or

another foreign object and cannot return to the home

position. Turn the printer off. Open the printer cover and

remove any paper or other obstructions from the paper

path. Then turn the printer back on. If the error does not

clear, contact Epson.

The printer's ink pads are nearing or at the end of their

service life. Contact Epson to replace the ink pads. If the

ink pads are nearing the end of their service life, printing

Flashing

can be resumed by pressing the

alternately

A firmware update did not complete and the printer is

in recovery mode. Try updating the firmware again or

contact Epson.

Flashing fast

paper button.

paper button to

paper button.