Cisco Codec C Series Посібник для початківців - Сторінка 19
Переглянути онлайн або завантажити pdf Посібник для початківців для Конференц-система Cisco Codec C Series. Cisco Codec C Series 42 сторінки. Telepresence conference system
Також для Cisco Codec C Series: Посібник для початківців (41 сторінок), Посібник користувача (44 сторінок), Посібник для початківців (35 сторінок), Посібник для початківців (32 сторінок), Посібник для початківців (46 сторінок)
Друкувати сторінку
Cisco TelePresence Video Systems
Contents
Configuring IP
(when not set by a provisioning system)
Your video conference system supports both iP version 4
(iPv4) and iP version 6 (iPv6). in both cases, the iP param-
eters can be assigned automatically by the network, or you
can set everything manually.
if you want to set the parameters manually please contact
your network administrator to obtain the required parameters.
if an iP address is already assigned to your system, you find the
current iPv4 and/or iPv6 address on the System information
page:
Go to
Home > Settings > System
information.
the iPv4 Address and/or iPv6 Address of the system is shown
in the
Network
section on the System information page.
Press
Exit
(the right most function key) to exit.
NoTe:
You must restart the system after changing the iP
settings for the changes to take effect
Always save the new value when you change a setting
• drop down list selection: Navigate to the correct value
and press the
OK
( )
key to save, or press the left arrow
key
to leave without saving.
• text entry in an input field: enter the text, navigate to
Ok/Save
to save the change, or navigate to
leave without saving; then press
theOK
Back to task overview
D14639.09 Video Systems Getting Started Guide TC6.1, April 2013.
Introduction
User interfaces
To set or change the IPv4 settings
1. Select IP version
Go to
Home > Settings > Administrator settings > Advanced
configuration > Network
2. Select automatic or manual IP assignment
Go to Assignment. Select
assignment; select
manually.
a. if you selcted DHCP, the iP configuration is complete.
b. if you selected Static, go to
Subnet
and enter the dNS server address in the
Address
3. Press
Home
*) iP assignment:
dHCPv6: All iPv6 addresses, including options, are obtained automatically
from a dHCPv6 server.
Autoconf: the system and gateway iP addresses will be assigned
Cancel
to
automatically. the options, e.g. NtP and dNS server addresses, must be
( ) key
to confirm.
set/assigned according to the dHCP options setting. **
Static: the system and gateway iP addresses must be configured
manually. the options, e.g. NtP and dNS server addresses, must be set/
assigned according to the dHCP options setting. **
Confirguration
Configuration
1. Go to
IPStack
and select
IPv4.
DHCP
if you want automatic iP
Static
if you want to set the iP addresses
IPv4
and enter the Address,
Mask, Gateway. Go to the
DNS Server
section
Server 1
input field.
(
)
to return to the home menu.
19
Getting Started Guide
Appendices
To set or change the IPv6 settings
1. Select IP version
Go to
Home > Settings > Administrator settings > Advanced
configuration > Network
1. Go to
IPStack
2. Select automatic or manual IP assignment
Go to
IPv6 >
assignment.Select
Autoconf
ment
drop down list if you want automatic iP assignment;
select
Static
if you want to set the iP addresses manually.
a. if you selected Autoconf, go to
on or off according to your preference.*
b. if you selected Static, go to
Address
iP address. Go to Gateway.and enter the gateway
address. Set
DHCPOptions
to on or off according
to your preference.**
3. Set DNS and NTP server addresses
if dHCP options are switched off, you must set the dNS
and NtP server addresses in
Advanced
Go to the
DNS Server
section and enter the dNS server
address in the
Server 1 Address
input field.
to set the NtP address go to
Network services > NTP
and set the address. Select
save
to confirm the address.
Set
Mode
to Auto.
4. Press
Home
(
)
to return to the home menu.
**) dHCP options:
on: the iP parameters, like the dNS and NtP server addresses, will be
obtained automatically from a dHCPv6 server.
off: the iP parameters, like the dNS and NtP server addresses, must be
set manually.
Copyright © 2010–2013 Cisco Systems, Inc. All rights reserved.
Contacts
and select
IPv6..
in the
IP assign-
DHCP Options.
Set to
and enter the
configuration.