Epson L200 Посібник з експлуатації - Сторінка 25

Переглянути онлайн або завантажити pdf Посібник з експлуатації для Принтер "Все в одному Epson L200. Epson L200 47 сторінок. Color inkjet printer
Також для Epson L200: Технічні характеристики (4 сторінок), Посібник користувача (4 сторінок), Інструкція (4 сторінок), Почніть звідси. (2 сторінок), Посібник користувача (2 сторінок), Повідомлення та гарантія (12 сторінок)

Друкувати сторінку

L200/L201/L100/L101

LD Roller Assy / LD Roller

Step 1

Step 2

Gear 23T

Shaft Gear 24T

Step 2, 3

Pick Assy

Bearing

Concave section

Shaft Gear 24T

When removing the LD Roller Assy, follow the procedure below.

1. Release the hooks (x2) and remove the Gear 23T.

2. Release the hooks (x2) and slide the Shaft Gear 24T to the 0-digit side until the concave section of the gear comes to the bearing part of the

Pick Assy.

3. Remove the LD Roller Assy upward.

When removing the LD Roller, remove the screws (x2) shown in the figure above.

When install the Torsion Spring, make sure to align the leg to the position as shown above.

Carriage

Compression Spring

Guide Carriage

Grounding Plate

Protrusion

Positioning Hole and Dowel

Hook

When replacing the Carriage, be careful about the following and

remove the Grounding Plate, Guide Carriage, Compression Springs

from the Carriage to be replaced, then attach them to the new

Carriage as shown in the figure above.

Insert the protrusion of the Grounding Plate to the hole of the

Carriage, and align the dowels (x3) of the Carriage with the

positioning holes (x3) of the Grounding Plate.

Secure hooks (x2) of the Guide Carriage by attaching them on

the holes (x2) of the Carriage.

Disassembly/Assembly

LD Roller Assy

LD Roller

LD Roller Assy

Torsion Spring

C.B.P-TITE SCREW 3x8 (TBD)

C.F.B-TITE SCREW 3x5 (TBD)

Hook

Porous Pad Front Paper Guide

Standard surface:

In the area with concaves and convexes on the

Porous Pad Front Paper Guide, use the level

of the concave section as a standard surface.

When installing the Porous Pad Front Paper Guide, align the pad

with the ribs and protrusions of the Platen. After installing the pad,

make sure to fit it evenly 1.5mm lower than the standard surface.

Details of Disassembling/Reassembling by Parts/Unit

Friction Buckler

Friction Buckler R

Friction Buckler

Housing Bucklers

Leg of the

spring

Friction Buckler R

When installing the Friction Buckler and Friction Buckler R to the Housing Buckler, pay attention to the following instructions.

•

Remove the Sheet BF2-A on the rear side of the Friction Buckler to be replaced, and secure the removed sheet with double-sided tape to the

new Friction Buckler.

•

Install the friction bucklers to the Housing Bucklers with the cutouts facing forward.

Install the buckler to the position as shown above.

Jam Cover

Rib

Protrusion

When removing the Jam Cover, be careful not to lose the spring

installed to the dowel on the right side.

Housing Buckler

Sheet BF2-A

Double-sided

tape

Friction Buckler

Cutouts

Housing Buckler (Friction Buckler R)

Jam Cover

Spring

The USB Cover cannot be re-used once it is removed. Whenever

the cover is removed, make sure to replace it with a new one.

When removing the USB Cover, cut the hook securing the USB

Cover with a nipper. Be careful not to damage the Upper Housing

then.

Revision A

Housing Buckler (Friction Buckler)

USB Cover

Hook

Confidential