Cisco TelePresence Інструкція з монтажу - Сторінка 2

Переглянути онлайн або завантажити pdf Інструкція з монтажу для Конференц-система Cisco TelePresence. Cisco TelePresence 2 сторінки. Configuring a cisco unified communications manager sip trunk with a cisco telepresence content server
Також для Cisco TelePresence: Брошура (4 сторінок), Технічні характеристики (7 сторінок), Посібник з монтажу (4 сторінок), Посібник адміністратора (27 сторінок), Короткий довідник (2 сторінок), Посібник (24 сторінок)

Друкувати сторінку
Cisco TelePresence Інструкція з монтажу
Installing Cisco TelePresence System Profile 52" Dual
4
Unpack the monitor box and lift out the monitors. Fasten the monitors to the bottom module
and mount the camera bracket
Speaker grille box
Unpack the
monitor box.
Lift out to open the
snap lockers.
See the two triangular
MOUNTING THE MONITORS
holes in the base.
Use the holes to help
1.
Carefully lift the right monitor out of the
steering the monitor
packaging as illustrated.
to enter the poles on
See the two triangle holes in the monitor
2.
the column.
base. Use these holes to help steering the
monitor to enter the poles on the column.
Repeat the above procedure for the left
3.
monitor.
6
Mounting the camera cables and the camera
MOUNTING THE CAMERA CABLES
Locate the camera cables in the bottom module (the two long cables).
1.
2.
Locate the hole in the monitor where the cables can be pushed
through. Push the cables through the hole in the right monitor.
3.
On the rear side, place the cables in the foam rails that are going on
the rear side of the monitor.
78-19776-01revB Profile 52 Dual Installation Sheet | April 2012 | © 2010-2012 Cisco Systems, Inc. All rights reserved.
MOUNTING THE MONITORS, continued
4.
Align the monitors at the top and fasten the two
monitors together using the upper monitor bracket
LIFTING HANDLES. Locate the
and the M4×25 screws.
orange lifting handles in the front
HEAVY
and rear side of the monitor.
5.
Fasten the two monitors together at the bottom using
CAUTION
the lower monitor bracket and the M4×8 screws.
Fasten the monitor to the column poles using
6.
four M8×16 screws, two screws at each monitor.
7.
Tighten the monitor gently to the bottom module until
the monitor cannot be moved anymore.
Left monitor
Right monitor
4 * M8×16
Allen key
MOUNTING THE CAMERA
1.
Connect the RJ45 and HDMI cables to the camera, see illustration.
2.
Loosen the wing nuts on the camera bracket and move the bracket to
the rear position.
3.
Place the camera on the bracket and slide the bracket with the camera
towards the front and tighten the wing nuts.
4.
Place the camera cables in the foam rails.
CAMERA CABLE CONFIGURATION
PrecisionHD 1080p
RJ45
HDMI
For countries with 60 Hz current frequency
you must set the PrecisionHD 1080p camera
DIP switch to: 00100.
MOUNTING THE CAMERA BRACKET
1.
Fasten the camera bracket using two wing nuts.
Camera bracket
Upper monitor
bracket
Lower monitor
bracket*
* The lower monitor bracket is not used on a wall
mounted system. Instead, make sure the monitors
are aligned at the front.
7
Finishing up
MOUNTING THE BACK COVER
1.
Enter the back cover on top and
snap it on place with the magnets.
The magnets are strong. Make sure
your fingers are not trapped.
2.
Remove the plastic cover in front of
the monitor.
3.
Remove the plastic foil on the
monitor frame.
4.
Snap on the speaker grille to the
front.
5.
Use the supplied cloth to clean the
system.
Page 2
5
Connect the monitor cables to the left and right monitor
Left monitor connectors
B
B
Power
HDMI 1
Right monitor connectors
B
HDMI 1
Speaker in
B
CONNECTING MONITOR CABLES
Open the front door and locate the monitor connectors and cables.
A 级声明 (A Class product declaration)
Connect the left monitor:
Connect the right monitor:
1.
HDMI cable
1.
HDMI cable
2.
Speaker in (15 pin DSUB from DNAM)
2.
Speaker in (15 pin DSUB from DNAM)
本产品为 A 级 ITE，在其使用说明，铭牌等显著位置中已包含如下内容的声明
3.
Power cable
3.
Power cable
(We declare here that the subject product is A class ITE product, and the
following statement is clearly marked in the user manual or nameplate):
EMC Class A declaration
警告
此为 A 级产品。在生活环境中，该产品可能会造成无线电干扰。在这种
情况下，可能需要用户对干扰采取切实可行的措施。
WARNING:
WARNING:
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
8
Connect the system
1.
Open the rear door and route the cables out through the opening at the lower part of the door.
声明所在位置 (Position of the Declaration):
使用说明 User Manual
2.
Close the rear door carefully.
铭牌 Nameplate
3.
Place the microphones on the table, connect the microphone cables and place the PC cable
on the table.
4.
申请号 (Application No.)：
Connect the Ethernet cable.
申请人 (Applicant):
5.
Connect the power cable, use the country specific power cable that came with the system.
型号
(Model Number)：
6.
Open the front door and turn on the monitor.
7.
Follow the instructions in the accompanying Touch Screen CS installation guide to connect and
initialize the touch screen.
8.
The system should be up and running in a few minutes.
签字/盖章 Signature/Stamp:
日期 Date:
The rear door
Microphone cable
Power cable
Speaker in
Power
Ethernet cable
PC cable