Cisco TelePresence ProfileSeries Посібник для початківців - Сторінка 27
Переглянути онлайн або завантажити pdf Посібник для початківців для Конференц-система Cisco TelePresence ProfileSeries. Cisco TelePresence ProfileSeries 42 сторінки. Telepresence ex, mx, quick set c20, codec c, sx20 quick set, profile series video systems
Друкувати сторінкуCisco TelePresence Systems
GettinG started Guide
Table of contents
Introduction
Web interface
Configuring H.323 and SIP
(when not set by a provisioning system)
To get online and ready to place and receive calls, your
system must be set up properly. Your system will use either
the H.323 protocol or the SIP protocol for video calls.
NoTE:
Contact your system administrator, or service
provider, for information about the network settings.
For networks administered through Cisco TMS (Cisco
TelePresence Management Suite) your Cisco TMS
administrator will help you to get online.
Back to task overview
D14639.06 Video Systems Getting Started Guide (TC5.1) | 2012 FEBRUARY | © 2011-2012 Cisco Systems, Inc. All rights reserved.
User interfaces
Configuration
Configuration
H.323
If in doubt for any of the parameters below, contact your
system administrator or your service provider.
1. Go to the
Configuration
tab and select
Configuration.
Open the
H323
settings from the left column.
2. Under the
H323 Alias
heading, enter the
number in their respective input fields.
3. Go to the
Gatekeeper
heading.
If you want the system to obtain the H.323 gatekeeper
address automatically, select
down list; if you want to enter the address manually,
select
Manual.
If set to
Manual
enter the gatekeeper
corresponding input field. Click
4. If the H.323 gatekeeper requires authentication and
you want your system to authenticate itself to the
gatekeeper, go to the
Authentication
select
On
in the
Mode
drop down list. Then enter the
LoginName
and
Password
in the corresponding input
fields. Click
ok
to save the change.
Otherwise, select
Off
in the
Mode
5. Go to the
Diagnostics
tab and select
to verify the H323 settings.
If you successfully registered to a Gatekeeper the
will show
Registered
in the H323 section.
Please check the Administrator guide for your product if you
want to change the other H.323 settings.
Appendices
SIP
If in doubt for any of the parameters below, contact your
system administrator or your service provider.
Advanced
1. Go to the
Configuration.
Open the
ID
and
E164
2. Enter the SIP URI in the
display name in the
save the change.
3. Select the preferred transport protocol from the
DefaultTransport
Auto
in the
Discovery
drop
system will first try to connect using TLS, then TCP, and
finally UDP.
Address
in the
4. Select a proxy type in the
ok
to save the change.
default type is Standard.
5. Go to the
If you want the system to obtain the SIP proxy address
heading and
automatically, select
list; if you want to enter the address manually, select
Manual.
If you select
drop down list.
corresponding input field. Click
System Information
6. If the SIP proxy requires authentication you must enter a
login name and password to authenticate your system.
Status
Go to the
LoginName
fields. Click
7. Go to the
to verify the SIP settings.
If you successfully registered to a SIP server the
will show
Please check the Administrator guide for your product if you
want to change the other SIP settings.
Configuration
tab and select
Advanced
SIP
page from the sidebar on the left.
URI 1
input field, and optionally a
DisplayName
input field. Click
ok
drop down list. If you select Auto, the
Type
drop down list. The
Proxy 1
heading.
Auto
in the
Discovery
drop down
Manual
enter the proxy
Address
in the
ok
to save the change.
Authentication 1
heading and enter the
and
Password
in the corresponding input
ok
to save the change.
Diagnostics
tab and select
System Information
Status
Registered
in the SIP section.
www.cisco.com
27
to