Sony SA-WCT291 Посібник з експлуатації - Сторінка 3

Переглянути онлайн або завантажити pdf Посібник з експлуатації для Стереосистема Sony SA-WCT291. Sony SA-WCT291 24 сторінки. Sound bar and active speaker system
Також для Sony SA-WCT291: Посібник з експлуатації (42 сторінок)

Друкувати сторінку

UNLEADED SOLDER

Boards requiring use of unleaded solder are printed with the lead-

free mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

•

Unleaded solder melts at a temperature about 40 °C higher

than ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be

applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to

about 350 °C.

Caution: The printed pattern (copper foil) may peel away if

the heated tip is applied for too long, so be careful!

•

Strong viscosity

Unleaded solder is more viscous (sticky, less prone to ﬂ ow)

than ordinary solder so use caution not to let solder bridges

occur such as on IC pins, etc.

•

Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may

also be added to ordinary solder.

NOTE OF PERFORMING THE OPERATION CHECK IN

THE STATE THAT HEAT SINK WAS REMOVED

When performing the operation check in the state that this unit was

disassembled, it is possible to perform the operation check in the

state that heat sink was removed. But don't perform the operation

check in the long time, and perform the operation check in the

volume state as low as possible.

CAPACITOR ELECTRICAL DISCHARGE PROCESSING

When checking the board, for the electric shock prevention, con-

nect the resistors to both ends of capacitors to discharge the capaci-

tor as shown in the ﬁ gure below.

Note 1: When

the

connector

REGULATOR 3L411L board (US, CND) or SWITCHING

REGULATOR 3L411W board (Except US, CND, E12) or

SWITCHING REGULATOR 3L411W-1 board (E12) to the SUB

MAIN board is disconnected before discharging, completely

ﬁ nish discharging both boards, and then reconnect the connector.

If discharging is not complete, sparking may occur when

connecting the connector and cause a blown fuse.

Note 2: Be sure to discharge using a resistor of 800 Ω or higher.

(Do not discharge with a 0 Ω resistor)

Discharging at a point where excessive electric current ﬂ ows

through a fuse may cause the fuse to blow.

– SUB MAIN Board (Component Side) –

SECTION 1

SERVICING NOTES

that

connects

the

SWITCHING

800 /

2 W

C8138

C8140

– SWITCHING REGULATOR 3L411L Board

(US, CND) (Conductor Side) –

– SWITCHING REGULATOR 3L411W Board

(Except US, CND, E12) (Conductor Side) –

– SWITCHING REGULATOR 3L411W-1 Board

(E12) (Conductor Side) –

MODEL IDENTIFICATION

Distinguish by Part No. and destination code on the rear side of

the subwoofer.

– Rear view –

MODEL NUMBER LABEL

Model

SA-WCT290 (Black): US, CND

SA-WCT290 (Black): AEP

SA-WCT290 (Black): UK

SA-WCT290 (Black): RU

SA-WCT290 (Black): E12

SA-WCT290 (Black): E3

SA-WCT290 (Black): EA

SA-WCT290 (Black): SP

SA-WCT290 (Black): AUS

SA-WCT290 (Black): TH

SA-WCT290 (Black): LA9

SA-WCT291 : AEP

SA-WCT291 : UK

SA-WCT291 : RU

SA-WCT290 (White): EA

SA-WCT290 (White): SP

SA-WCT290 (White): TH

• Abbreviation

AUS

: Australian model

CND : Canadian model

: 240 V AC area in E model

E12

: 220-240 V AC area in E model

: Saudi Arabia model

LA9

: Latin-American model

: Russian Model

: Singapore model

: Thai model

SA-WCT290/WCT291

C201

800 /2 W

Destination code

Part No.

4-688-018-0[]

4-688-018-1[]

4-688-018-2[]

4-688-018-3[]

4-688-018-4[]

4-688-018-5[]

4-688-018-6[]

4-688-018-7[]

4-688-018-9[]

4-688-019-0[]

4-688-019-2[]

4-688-020-0[]

4-688-020-1[]

4-688-020-2[]

4-693-270-2[]

4-693-270-3[]

4-693-270-5[]