Digitrax BDL16 Інформація про встановлення - Сторінка 9

Переглянути онлайн або завантажити pdf Інформація про встановлення для Датчики безпеки Digitrax BDL16. Digitrax BDL16 10 сторінок. Loconet occupancy detector with rx4

Друкувати сторінку

into one of the 4 occupancy LED headers, you can see the state of the zone and

occupancies for that header. This allows you to easily check the zone sensitivi-

ty (typically 22K ohms to give detection). This also aids in the determination

of detection number and activity for a track detection section. Many detection

problems are related to wiring problems or poor connections to the detection

section rather than to the actual BDL16. By using the display array, you can

eliminate the wiring issues from the equation and be sure that the BDL 16 is

set up correctly.

Remember, if the zone power is OFF, the occupancy LEDs should be set up so

that they will be on to be sure that signaling systems or a CTC/dispatcher will

see the detection section in its most restricted aspect.

11.4 LocoNet Debug

If you are using LocoNet for reporting, be sure that the configuration is correct

for your usage. In normal operations the red "option" LED will blink ON

briefly when valid LocoNet messages are seen confirming a good LocoNet net-

work connection.

11.5 Analog Locomotives

The motor inductance of analog locomotives may in some installations cause

cross talk among the BDL16 detection sections. The addition of a 220ohm

3watt power wire wound resistor between the booster track terminals (Rail A

and Rail B on Digitrax boosters) will typically reduce the effect of this cross

talk. Simply use a leaded resistor as a jumper between the booster's two track

terminals.

12.0 Warranty and Repair Information

Digitrax guarantees the BDL16 to be free from manufacturing defects

for five years from the date of purchase. These units are not user service-

able. If a defect occurs, return the unit to Digitrax for service. Digitrax

will repair or replace BDL16s at our discretion at no charge to you for one

year from purchase date. This warranty excludes damage due to abuse,

such as failure to properly protect against input over current with a fuse or

circuit breaker or applying excessive input voltage to the unit.

Digitrax will make non-warranty repairs needed because of physical

damage or electrical abuse at fair and reasonable rates.

All warranties on Digitrax products are limited to refund of purchase

price or repair or replacement of Digitrax products at the sole discretion of

Digitrax.

In the event that Digitrax products are not installed or used in accor-

dance with the manufacturer's specifications, any and all warranties either

expressed or implied are void. Except to the extent expressly stated in this

section, there are no warranties, express or implied, including but not lim-

ited to any warranties of merchantability or fitness for a particular purpose.

Digitrax, Inc. reserves the right to make changes in design and specifi-

cations and/or to make additions or improvements in its products without

imposing any obligations upon itself to install these changes, additions or

improvements on products previously manufactured.

13.0 FCC Information

Radio or TV Interference: (this information is MANDATED by the FCC) This equip-

ment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a residential

environment. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. However, there is no guarantee that inter-

ference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and the receiver.

-Connect the equipment into an outlet on a circuit different form that

to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Note that any modifications to the equipment not expressly approved by Digitrax voids

the user's authority to operate under and be in compliance with CFR 47 rules, as

administered by the Federal Communication Commission. Digitrax believes any

conscientiously installed equipment following guidelines in this manual would be

unlikely to experience RFI problems.