Cisco TelePresence Посібник з монтажу - Сторінка 4

Переглянути онлайн або завантажити pdf Посібник з монтажу для Мережеве обладнання Cisco TelePresence. Cisco TelePresence 4 сторінки. Configuring a cisco unified communications manager sip trunk with a cisco telepresence content server
Також для Cisco TelePresence: Брошура (4 сторінок), Технічні характеристики (7 сторінок), Посібник адміністратора (27 сторінок), Короткий довідник (2 сторінок), Посібник (24 сторінок), Інструкція з монтажу (2 сторінок)

Друкувати сторінку

Installing Cisco TelePresence System Profile 65" Presentation Unit

Mounting the two modules together

Main system: Remove the top grille and open the top

cover.

Main system: Remove the uppermost screw on the

monitor sides facing each other, using a 2.5 mm Allen

key and a 7 mm wrench. See illustration.

Both systems: Remove the uppermost screw on the

bottom modules, using a 3 mm Allen key and a 7 mm

wrench.

Move the units towards each other. Leave some

space for the joint profile.

Level and align the systems: Use the screws inside

the bottom module to adjust and align the two

systems. See the instructions in step 7.

Place the joint profile between the two systems.

Connect bottom modules: On the main bottom

module, fasten the long M4 screw from the inside of

the module through the joint profile and to the nut

on the nut plate. Do the same from the inside of the

presentation unit bottom module.

Connect the monitor: On the main monitor, fasten

the short M4 screw from the inside of the monitor

through the joint profile and to the nut on the nut

plate.

If further adjustments are needed do this with the

adjustments screws inside the bottom module.

Unpacking the Monitor box and mounting the monitor to the base

Carefully lift and place the monitor onto the base.

NOTE:

Requires 4

Open the top cover.

persons and lifting straps

hEAvY

to lift.

AND

Repeat step 6 b for the presentation unit.

BULKY

If further adjustments are needed to align the systems,

REQUIRES:

4 PEOPLE TO LIFT

do this with the set screws inside the base modules.

CAUTION

Connect the monitor: Fasten the short M4 screw from

the inside of the monitor through the joint profile and to

the nut on the nut plate.

LIFTINg STRAPS INCLUDED.

The lifting straps are found

in the box, together with the

monitor, ready for use.

NOTE:

The straps are not

fixed to the monitor. be

careful when lifting the

monitor so the straps do

not slide during the lifting

operation.

Main system

Uppermost screw

on the bottom

module

Cable hatch

Connecting cables

The cables goes from one

system to the other through the

cable hatch.

NOTE:

The main system has

already been connected, only

the extra cabling needed for the

presentation unit is shown here.

Mounting the grilles in front and finishing up

Close the top covers.

Snap on the top grilles.

Snap on the speaker grille.

Close the base module doors.

Remove the plastic foil on the

monitor frame.

Use the supplied cloth to clean

up the system.

Uppermost screw

on the monitor

The nut plates are placed

inside the joint profile

Joint profile with a

slot for the cables

Presentation unit

Power*

From DVI-I 4 on

the C90 codec

Close the doors and snap

on the speaker grille.

Page 2

Level and align the systems

The nut plates are placed

In order to level the systems, use 4 pcs of the (a) set screw in the holes marked in the

inside the joint profile

picture below for each bottom module. Note that the illustration depicts a base module

as seen from above, with the door open.

Loosen nuts before adjusting the pin bolts down. When proper adjustment have been

found, tighten nuts again. These are the same nuts which were mounted in step 2 C,

see the previous page.

In step 6 the joint profile

is mounted to the main

monitor.

(In step 8 the joint profile

is mounted to the second

monitor.)

A 级声明 (A Class product declaration)

本产品为 A 级 ITE，在其使用说明，铭牌等显著位置中已包含如下内容的声明

Presentation unit,

(We declare here that the subject product is A class ITE product, and the

base module

following statement is clearly marked in the user manual or nameplate):

EMC Class A declaration

此为 A 级产品。在生活环境中，该产品可能会造成无线电干扰。在这种

情况下，可能需要用户对干扰采取切实可行的措施。

WARNINg:

This is a class A product. In a domestic environment this product may cause radio

WARNING:

interference in which case the user may be required to take adequate measures.

This is a class A product. In a domestic environment this

product may cause radio interference in which case the user may be

required to take adequate measures.

Connect the power cable

Connect the presentation unit power cable. The cable is lead out from the rear side of

声明所在位置 (Position of the Declaration):

the main system.

申请号 (Application No.)：

申请人 (Applicant):

型号

(Model Number)：

* The power cable goes through

the cable hatch and to the rear side

of the main system.

Close the lids and

snap on the grilles.

4 × set screw (a)

Codec

Lid

警告

使用说明 User Manual



铭牌 Nameplate



签字/盖章 Signature/Stamp:

日期 Date:

Ethernet cable

PC cable

Microphone cables

Power cable

Power cable from

the Presentation unit