Cisco 7513 Series Інструкція із заміни Посібник із заміни - Сторінка 18
Переглянути онлайн або завантажити pdf Інструкція із заміни Посібник із заміни для Сервер Cisco 7513 Series. Cisco 7513 Series 22 сторінки. Chassis replacement
Також для Cisco 7513 Series: Посібник із швидкого старту (44 сторінок), Інструкція із заміни Посібник із заміни (26 сторінок), Технічний паспорт (11 сторінок), Посібник (30 сторінок), Підтримка (20 сторінок), Інструкція із заміни Посібник із заміни (19 сторінок)
Друкувати сторінку
Replacing the Chassis
Step 5
Step 6
Step 7
Step 8
Step 9
Step 10
18 Cisco 7513 Chassis Replacement Instructions
If the system does not go on, do the following. If it goes on, proceed to the next step.
•
First, check the source power. Ensure that the power switch is completely in the on (|)
position and that the power (input) cord is properly connected at both ends.
•
Check the fan OK LED. When on, this LED indicates the blower is operating. If the (AC
or DC) OK LED is off and the blower is not operating, there is most likely a problem
with the (AC or DC) input power or with one of the internal DC lines. If so, there are no
installation adjustments that you should make; contact a service representative for
further instructions.
Verify that the normal LED on the RSP2 goes on and stays on, which indicates that the
system software booted successfully. If the LED goes on, proceed to the next step. If it does
not go on, do the following:
•
Check the ejector levers and captive installation screws on the processor modules. If any
appear loose, use the ejector levers to reseat the module, then tighten the captive
installation screws to secure it. Toggle the power off and back on again.
•
If the RSP2 normal LED still remains off, note whether the CPU halt LED goes on, and
contact a service representative.
When the system boot is complete, the RSP2 begins to initialize the interface processors.
During this initialization, the LEDs on each interface processor behave differently (most
flash on and off). The enabled LED on each interface processor goes on when initialization
has been completed.
•
If the enabled LED on all interface processors goes on, the system has booted
successfully and is now functional.
•
If the RSP2 LEDs previously indicated a successful system boot, but none of the
enabled LEDs on interface processors go on, suspect that one of the interface processors
has shifted out of its backplane connector and hung the bus. Turn OFF the power, then
use the ejector levers to release each interface processor and reseat them in their slots.
(Refer to the section "Moving Processor Modules from the Old Chassis to the New
Chassis" on page 13 for removal and insertion steps.) Tighten all captive installation
screws; then return to Step 1.
If the enabled LED on a single interface processor remains off, suspect that the interface
processor has shifted out of its slot. Use the ejector levers to release the interface processor
and reseat it in the backplane. (Refer to the section "Moving Processor Modules from the
Old Chassis to the New Chassis" on page 13, for removal and insertion steps.) Tighten both
captive installation screws; then return to Step 1.
If an enabled LED still fails to go on after performing these steps, suspect that the specific
interface processor has failed. Contact a service representative.
Verify that the console terminal displays a script and system banner similar to the
following:
GS Software (RSP-K), Version 10.3(571), SOFTWARE
Copyright (c) 1986-1995 by cisco Systems, Inc.
Compiled Wed 10-May-95 14:46 by mpo
System Bootstrap, Version 4.6(1) [fc2], SOFTWARE
After the system initializes, use the various show commands to display the status of the
system and individual interfaces, and ensure that they are operating according to their
previous configuration. (For descriptions and examples of these commands, refer to the
following section, "Verifying the Installation Using show Command Descriptions and
Examples.")