Digitus 4016032464419 Посібник
Переглянути онлайн або завантажити pdf Посібник для PCI карта Digitus 4016032464419. Digitus 4016032464419 2 сторінки. M.2 ngff/nvme ssd pci express add-on card
Також для Digitus 4016032464419: Посібник (4 сторінок)
Друкувати сторінку
M.2 NGFF/NVMe SSD
PCI EXPRESS ADD-ON CARD
Manual
DS-33170
Product Introduction
This M.2 NGFF/NVMe SSD PCI Express Add-On Card is a multi-
functional NVMe conversion card it can support the PCIe
protocol NVMe SSD to connect directly to the motherboard,
or the SATA Protocol NVMe SSD to connect to the
motherboard SATA port with SATA cable. It supports ultra-
fast PCI Express V3.0 X4 lanes transmit bandwidth up to
32GT/S and Serial ATA v3.0 transmit speed up to 6Gbps. This
adapter improves system speed, and the efficiency of office
and entertainment.
Specification
Compliant with PCI Express Specification Revision 3.0
Compliant with Serial ATA Specification Revision 3.0
Support NVMe key B/M m.2 SSD including 2230, 2242,
2260, and 2280 drives
Backwards compatible with PCIE V2.0 and V1.0
mainboards
Drive sizes are 80, 60, 42 and 30mm
Support Any "M" Key M.2 SSD , "B" Key and
"B+M" Key M.2 SSD
B- Key interface can insert SSD of M.2 NGFF SATA
Protocol; then insert SATA cable to connect motherboard.
It also use PCI E to supply power without external power
supply
M-Key interface can insert SSD of M.2 NGFF PCI-E
Protocol, and PCI-E transmission data do not need to
access SATA cable to connect motherboard
The M.2 PCIe SSD gets its power supply form the
motherboard PCIe BUS slot 3.3v
Support operating system: Windows® 10, Windows® 8,
Windows® 8.1, Windows® Server 2012 R2, Linux, Fedora,
SUSE, Ubuntu, Red hat native drivers support PCIe NVMe
No driver is required because the driver is transparent to
the operating system
Package content
1 x M.2 NGFF/NVMe SSD PCI Express Add-On Card
1 x User's Manual
1 x Low profile bracket
System Requirements
Windows® 10, Windows® 8, Windows® 8.1, Windows®
Server 2012 R2, Linux 32bit or 64 bit
One available PCI-Express x4/ x8/ x16 slot
Hardware installation
Please first installe the M.2 M Key SSD and M.2 B Key
SSD into the NVMe adapter; then follow these steps:
1. Turn Off the power of your computer.
2. Unplug the power cord and remove your
computer's cover.
3. To install the card, carefully align the card's bus
connector with the selected PCIe slot on the
motherboard. Push the board down firmly.
4. Used the SATA cable to connect NVMe adapter to
the motherboard SATA port
5. Replace the slot bracket's holding screw to secure
the card.
6. Replace the computer cover and reconnect the
power cord.
Support:
If you have further questions, please contact our
customer support and you can find more information
on our homepage: www.assmann.com
Declaration
Hereby Assmann Electronic GmbH declares that the
Declaration of Conformity is part of the shipping
content. If the Declaration of Conformity is missing,
you can request it by post under the below mentioned
manufacturer address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany