Cisco 2621XM Посібник користувача - Сторінка 33

Переглянути онлайн або завантажити pdf Посібник користувача для Шлюз Cisco 2621XM. Cisco 2621XM 48 сторінок. Non-proprietary security policy
Також для Cisco 2621XM: Операції (25 сторінок), Посібник користувача (20 сторінок)

Друкувати сторінку

Place the seventh label on the router as shown in

Step 8

so that one half of the label covers the enclosure and the other half covers the right WAN interface card

slot. Any attempt to remove a WAN interface card will leave tamper evidence.

Step 9

Place the eighth label on the router as shown in

so that one half of the label covers the enclosure and the other half covers the Compact Flash slot. Any

attempt to remove a CF card will leave tamper evidence.

Step 10

The labels completely cure within five minutes.

To apply tamper-evidence labels to the Cisco 3745:

Step 1

Clean the cover of any grease, dirt, or oil before applying the tamper evidence labels. Alcohol-based

cleaning pads are recommended for this purpose. The temperature of the router should be above 10°C.

Step 2

Place the first label on the router as shown in

that the one half of the tamper evidence label covers the enclosure and the other half covers the right side

of the router. Any attempt to remove the enclosure will leave tamper evidence.

Place the second label on the router as shown in

Step 3

so that the one half of the tamper evidence label covers the enclosure and the other half covers the left

side of the router. Any attempt to remove the enclosure will leave tamper evidence.

Place the third label on the router as shown in

Step 4

that the one half of the label covers the enclosure and the other half covers the top-left Network Module

slot. Any attempt to remove a network module will leave tamper evidence.

Place the fourth label on the router as shown in

Step 5

so that the half of the label covers the enclosure and the other half covers the bottom-left Network

Module slot. Any attempt to remove a network module will leave tamper evidence.

Place the fifth label on the router as shown in

Step 6

that the one half of the label covers the enclosure and the other half covers the top-right Network Module

slot. Any attempt to remove a network module will leave tamper evidence.

Step 7

Place the sixth label on the router as shown in

that the half of the label covers the enclosure and the other half covers the bottom-right Network Module

slot. Any attempt to remove a network module will leave tamper evidence.

Step 8

Place the seventh label on the router as shown in

so that one half of the label covers the enclosure and the other half covers the left WAN interface card

slot. Any attempt to remove a WAN interface card will leave tamper evidence.

Place the eighth label on the router as shown in

Step 9

so that one half of the label covers the enclosure and the other half covers the middle WAN interface card

slot. Any attempt to remove a WAN interface card will leave tamper evidence.

Place the ninth label on the router as shown in

Step 10

that one half of the label covers the enclosure and the other half covers the right WAN interface card slot.

Any attempt to remove a WAN interface card will leave tamper evidence.

Place the tenth label on the router as shown in

Step 11

that one half of the label covers the enclosure and the other half covers the Compact Flash slot. Any

attempt to remove a CF card will leave tamper evidence.

The labels completely cure within five minutes.

Step 12

Cisco 1721, 1760, 2621XM, 2651XM, 2691, 3725, and 3745 Modular Access Routers and 7206-VXR NPE-400 Router FIPS 140-2 Non-Proprietary

OL-6083-01

The Cisco 1721, 1760, 2621XM, 2651XM, 2691, 3725, 3745, and 7206 VXR NPE-400 Routers

Figure