Pressing the # key after you have entered the value is very important.
If you do not press #, the system will automatically timeout after 10
seconds. The normal sequence is " code # value # 3 ".
Once the IP address, default gateway and subnet mask are entered into the
ATA, use the menu mentioned alongside to check the parameters you have
entered.
Finding out the IMAGE your ATA is loaded with :
Once the ATA is configured and you receive the IP address, go to the following site: http://xxx.xxx.xxx.xxx/dev, where
"xxx.xxx.xxx.xxx" represents the IP address assigned to ATA (either static or through DHCP).
If you have assigned a private IP address to your ATA then you can only view the configuration from the PC which has to be on the
same LAN subnet. If the IP address of ATA is a public one then the configuration can be viewed from any PC which is on internet.
After you are able to view the configuration page of the ATA, check out the image your ATA is loaded with & then proceed to the
respective chapter to configure the other parameters as per the image.
The image can be viewed at the bottom of the configuration page. The ATA may be loaded mainly with one of the following images :
1.
SIP image with which the ATA will support only SIP protocol :
ata000d6508e9ab
Version: v3.1.0 atasip (Build 040211A)
MAC: 0.13.101.8.233.171
SerialNumber: INM072861V6
ProductId: ATA186I1
Features: 0x00000000
HardwareVersion: 0x0006 0x0000
Go to the chapter " configuring account , network & Codec settings of ATA for SIP "
2.
H323 image with which the ATA will support only H.323 Protocol :
ata000e8349dd31
Version: v3.1.1 atah323 (Build 040629A)
MAC: 0.14.131.73.221.49
SerialNumber: INM074715XA
ProductId: ATA186I1
Features: 0x00000000
HardwareVersion: 0x0006 0x0000
Go to the chapter " configuring account, network & Codec settings of ATA for H.323 "
3.
Image with support for both SIP & H.323 protocol :
ata000d6508d994
Version: v2.16 ata18x (Build 030401a)
MAC: 0.13.101.8.217.148
SerialNumber: INM07276617
ProductId: ATA186I1
Features: 0x00000000
HardwareVersion: 0x0006 0x0000
If your ATA is loaded with the above image which supports both SIP & H.323, it is recommended that the ATA should be configured
for H.323.
Go to the chapter " configuring account, network & Codec settings of ATA for H.323 "
Configuring Account,Network & Codec Settings for H.323 :
Once you get the ATA configuration page on the browser, please enter/check the following values:
1)
UIPassword is to be set to access password which will be known only to the user – recommended to have for security reasons
so that others cant make changes to the configuration.
2)
UseTftp is to be set to 0.
Set Dhcp to 0 (Disabled) if you want to assign static IP address to ATA. If you want the ATA to get the IP address dynamically
3)
assigned then set this to 1 (enabled). In the most common scenario it is 0.
4)
StaticIP is to be set to the IP allotted by the ATA
5)
StaticRoute to be set to the default gateway entered earlier into the ATA.
6)
StaticNetMask to be set to the mask entered earlier into the ATA.
(N.B.: you have already configured 3,4,5 parameters through IVR else you won't be able to view the ATA configuration on
your browser.)
IVR parameter
check code
80#
23#
22#
2
Parameter
IP Address
Subnet Mask
Gate Way IP address
Друкувати сторінку