Epson CX6600 - Stylus Photo Printer Посібник "Почніть тут - Сторінка 7

Переглянути онлайн або завантажити pdf Посібник "Почніть тут для Аксесуари для принтерів Epson CX6600 - Stylus Photo Printer. Epson CX6600 - Stylus Photo Printer 8 сторінок. Epson scan icm updater v1.20 (psb.2008.07.001)
Також для Epson CX6600 - Stylus Photo Printer: Інформаційний посібник (4 сторінок), Короткий посібник (48 сторінок), Посібник "Почніть тут (8 сторінок), Посібник (14 сторінок), Посібник з оновлення (2 сторінок), Посібник з налаштування (2 сторінок), Оновлення (1 сторінок), Короткий посібник (47 сторінок), Посібник з експлуатації (50 сторінок)

Друкувати сторінку
Epson CX6600 - Stylus Photo Printer Посібник
14
Plug the flat end
of the cable into
any available USB
port on your
Macintosh.
Follow the instructions below to add the Stylus CX to the
Print Center or Printer Setup Utility (for OS X) or the Chooser (for OS 9).
Selecting the Stylus CX for Mac
1
Open the OS X Applications folder, then open the Utilities folder and
start Print Center or the Printer Setup Utility.
If you see this screen, click Add.
2
On the Printer List screen, click the
Add button.
3
On the next screen, select EPSON USB from
the pop-up menu.
4
Click Stylus CX6600.
Note: If the CX6600 doesn't appear, make
sure it is turned on and securely connected
to your Macintosh.
5
Click the Add button. You see the Stylus CX6600 in the Printer List.
6
Quit Print Center or the Printer Setup Utility. Now you're ready to copy,
scan, and print. See the Quick Guide or your on-screen CX6600
Reference Guide for instructions.
7
If you use Classic Mode applications, install the software on OS 9 also.
Selecting the Stylus CX for Mac OS 9
1
Open the Chooser from the Apple
2
Select CX6600 Series, then select
your USB port and turn on
background printing.
3
Close the Chooser. Now you're
ready to copy, scan, and print. See
the Quick Guide or your on-screen
CX6600 Reference Guide for
instructions.

Any Problems?

If the red
!
error light is on, check the message on the Stylus CX. Try
turning the Stylus CX off and then back on to clear the error. If your
problem is listed here, try these suggestions. For more information, see
your Quick Guide, software Help, or on-screen CX6600 Reference Guide.
The Found New Hardware
Wizard appears on
your screen.
You see an error message
when you try to print
or scan.
The Stylus CX
doesn't work.
®
OS X
®
menu.
Click Cancel and follow the steps in
section 6. Disconnect the Stylus CX
before installing the software.
Make sure your Stylus CX is connected to
your computer, plugged into a power
source, and turned on.
Make sure you removed the tape from the ink
cartridge holder, as described in section 1.
Turn the Stylus CX off and then on again.
Make sure the ink cartridges are pushed
all the way down.
Check the LCD screen to see if you or
someone else set the Security Lock. See
your Quick Guide for details.
Make sure your Epson Stylus CX6600
software is installed correctly.