Crow GENIUS Інструкція з монтажу та інструкція з використання

Переглянути онлайн або завантажити pdf Інструкція з монтажу та інструкція з використання для Датчики безпеки Crow GENIUS. Crow GENIUS 2 сторінки. High performance double dual tm element passive infrared intrusion detector asic technology for higher reliability

Друкувати сторінку

CROW SCIENTIFIC RESEARCH

GENIUS

HIGH PERFORMANCE

DOUBLE DUAL

ELEMENT

PASSIVE INFRARED INTRUSION

DETECTOR ASIC TECHNOLOGY

FOR HIGHER RELIABILITY

ELECTRONIC ENGINEERING LTD.

INSTALLATION INSTRUCTIONS

P/N: 71ii113

IMPORTANT:

In an environment with a small animal:

1. The GENIUS has to be mounted at 2.1m

(7ft.) or higher (max 3.0m or 10ft.) above floor

level.

2. Install the GENIUS vertically (not titled

forward).

3. Away from furniture 2.1m (7ft.) or more, on

which a small animal may jump.

4. Not facing a staircase, ladder or similar

object which can be part of the monitored

environment (the vertical motion of the animal

may be interpreted by the detector as an

actual intruder).

5. Flip dipswitch #1 to the "ON" (up) position for

a harsh environment.

6. Calibrate the GENIUS according to the

vertical calibration charts.

Table 1 - For wide angle lens (lens code GE01)

Table 2 - For long range lens (lens code GE02)

Table 3 - For vertical curtain lens (lens code

GE03)

VERTICAL CALIBRATION CHARTS

TABLE 1 - WIDE ANGLE LENS (GE01)

Vert. Cal.

-5

-4

-3

-2

-1

Mt. Hgt.

2.1m

(7ft)

(19.8)

(26.4)

(33.0)

(39.6)

(46.2)

2.4m

(8ft)

(26.4)

(33.0)

(39.6)

(46.2)

(52.8)

2.7m

(9ft.)

(33.0)

(39.6)

(46.2)

(52.8)

(59.4)

OVER

(10ft.)

(39.6)

(46.2)

(52.8)

(59.4)

RANGE

TABLE 2 - LONG RANGE LENS (GE02)

Vert. C al

-5

-4

-3

-2

-1

M t. H gt

2.1m

(7ft)

(26.4) (36.3) (49.5) (59.4) (69.3) (82.5) (92.4) (100.5)

2.4m

(8ft)

(36.3) (49.5) (59.4) (69.3) (82.5) (92.4) (100.5)

2.7m

(9ft.)

(49.5) (59.4) (69.3) (82.5) (92.4) (100.5)

30.5

(10ft.)

(59.4) (69.3) (82.5) (92.4) (100.5)

GENERAL DESCRIPTION

Crow's GENIUS uses ASIC microprocessors to

achieve performance previously considered

beyond the limits of PIR intrusion technology.

This performance is predicated on science, not

magic. This TWIN DUAL ELEMENT PIR detector

is based on the latest "ASIC" (Application

Specific Integrated Chip) and SMD technologies.

The GENIUS monitors the environment by

analyzing the conditions and adapts to it

constantly. If conditions change, the GENIUS

adapts it maintaining sensitivity levels and

detection capability.

By using Twin Dual Optic Systems with a

diagonally opposed configuration (phase shift

discrimination), the GENIUS is able to achieve a

three dimensional thermal image of the protected

area. It stores this image and refers to it

determine intrusions.

During the standby mode (no LED indications)

the GENIUS constantly monitors the protected

area, updating and reconfiguring itself as

conditions change

In the GENIUS, user input is minimized to

vertical calibration and two switches.

DIP SWITCH SETTING

PULSE COUNT

Provides control for normal or high risk operating

environments.

Position Off (down)

This setting is for a stable environment without air

drafts.

Position On - AUTOMATIC PULSE COUNT

The

GENIUS

appropriate pulse count level (2 or 3) according to

the strength of the incoming signals.

This setting is for operation in a harsh environment

with air drafts or with a small animal less then

25cm in Height and less then 8kg. In Weight.

In HARSH mode, the GENIUS will increase its

sampling rate and take more factors into

account.

Note:

In HARSH mode the MINIMUM MOUNTING

HEIGHT MUST BE 2.1m (7ft.).

LED CONTROL SELECTION DipSwitch - marked 2

Position Off (down)- LED ENABLE - The led will

light when the

Position On - LED DISABLE - The led is disabled.

TABLE 3 - VERTICAL CURTAIN LENS (GE03)

Vert. Cal.

-5

M t. Hgt.

2.1m

(7ft)

(19.6)

(52.8)

(59.4)

2.4m

OVER

(8ft)

(26.4) (33.0) (39.6) (49.5) (59.4) (67.65) (74.25)

(59.4)

RANGE

2.7m

OVER

(9ft.)

(33.0) (39.6) (49.5) (59.4) (67.65) (74.25)

RANGE

OVER

(10ft.)

(39.6) (49.5) (59.4) (67.65) (74.25)

RANGE

MOUNTING THE DETECTOR

A variety of mounting positions is possible with

the standard GENIUS housing.

1. Open the front cover of the housing by

30.5

pushing the middle of its lower surface and

lifting upwards.

30.5

OVER

2. Snap out the detector PCB with his plastic

RANGE

cover.

30.5

OVER

RANGE

OVER

RANGE

–

dipswitch marked 1 (Fig. 1)

will automatically select the

GENIUS

Is in alarm condition.

-4

-3

-2

-1

20.5

22.5

(26.4)

(33.0)

(39.6)

(49.5)

(59.4)

(67.65) (74.25)

20.5

22.5

OVER

RANGE

20.5

22.5

OVER

RANGE

20.5

22.5

OVER

RANGE

MOUNTING LOCATION

Choose a location most likely to intercept an

intruder. See the detection patterns in Fig. 4 Fig.

5 and mounting alternatives in Fig. 2.

The twin dual element high quality sensors

detect motion across the beam field; they are

slightly less sensitive to motion towards the

detector.

While the GENIUS is capable of detecting

intrusions under exceedingly difficult conditions,

it is recommended to avoid the following

locations:

• Areas where sunlight may shine directly onto

the PIR (lens).

• Facing surfaces that may change

temperature extremely rapidly.

•

Areas with extreme air flows.

Suggestion: Minimum mounting height of

2.1m (7ft.) on wall with (-1) board calibration in

an environment with a small animal.

FIG. 1 – DETECTOR WITHOUT UPPER

COVER

PYRO SENSOR 1

1 2

PYRO SENSOR 2

TAMPER

SWITCH

3. The GENIUS housing can be mounted in a

variety of ways. The circular indentations in

the housing indicate mounting holes to be

punched out in accordance with the desired

mounting position :

• For surface mounting punch out the 4

indentations marked " A " (see Fig. 2).

• For Corner mounting gives 45° angle on

either the right or the left side. Punch out the

indentations marked " B " (see Fig. 2)

4. The circular indentation at the bottom of the

wiring channel of the base is the knockout

hole for wire entry. You may also use

mounting holes that are not in use for running

the wiring into the detector.

To close the front cover, insert the two small

prongs along its upper edge into their

corresponding slots in the upper edge of the

base. Insert the larger prong at the bottom of

the front housing into the slot at the bottom of

the base by exerting slight pressure on the

prong. The front cover should now fit snugly

into the base.

- 5