Argos Manhattaan 432/5114D Інструкція зі встановлення та монтажу - Сторінка 2
Переглянути онлайн або завантажити pdf Інструкція зі встановлення та монтажу для Вентилятор Argos Manhattaan 432/5114D. Argos Manhattaan 432/5114D 4 сторінки. Clear sat nickel rc ceiling fan
FIGURE 2
CANOPY
SCREW
BAYONET
SLOT
ROUND HOLE
FIGURE 3
DOWNROD
EARTH TERMINAL
N
LIGHT SUPPLY
(RED)
L
WIRES TO FAN
RECEIVER
L
N
PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
Please read these instructions carefully before attempting to install this ceiling fan. It is also advis-
able to keep these instructions in a safe place for future reference.
Before installing and using this ceiling fan, read the list of Do and Don'ts below.
Do not use the ceiling fan and open gas heating appliances in the same room at the same time.
It is important that the correct electrical connections are made and that the mountingplate is fitted
to an adequate ceiling support. Ceiling fans are heavy, so it is important that they should be
suspended securely. If in any doubt about the installation of this product consult a qualified
electrician.
This product must be installed in accordance with national building regulations.
When deciding on the location for your ceiling fan make sure that there will be plenty of room for
the rotation of the fan blades and that no obstacles are likely to get in their way. The distance
betweenthe fan blades and the floor should be at least 2.3m (7½ft).
Crosshead and slotted screw drivers
1xMax.40w E14 buld(NOT INCLUDED)
Step ladder
Insulating tape
MOUNTING PLATE
Remove the upper polystyrene cover from the box .Take the motor out of the box and place it on
the polystyrene cover ,or on a soft padded surface to protect it during the installation procedure.
Keep all packing material for future protection in transit.
BALL JOINT
CANOPY
1.Unscrew the four screws on the ceiling canopy to release the mounting plate(Figure 1). Secure
the mounting plate to a ceiling joist ,or an equally secure ceiling structure using the two wood fix-
ing screws and washers supplied. The support for the mounting plate must be capable of safety
and securely holding the moving weight of the fan. Note that additional strengthening of the joist
might be necessary.
2.For best fan performance and safety,make sure the mounting plate is fitted to a level ceiling
joist or ceiling support. If the mounting position is not level, hard packing material should be used
to make the plate level.
RECEIVER
1.Hang the ball joint and the fan onto the bracket. Make sure the guled pon of bracket is fitted
into slot of ball joint.(Figute 2) With the fan suspended in this manner, you can now make the
appropriate electrical connections. See the CONNECTION TO THE LIGHT CIRCUIT section.
2.insert the remote control receiver betwwen the bracket and the downrod. And the sensor as
shown.(Figure 2)
3.Fix conopy onto the bracket by tightening the screws.(Figure 4)
MATE
Ensure electricity is switched off at the mains before installing or maintaining this fitting.
CONNECTOR
Any switches connected to the ceiling fan must conform to the necessary British Standards. If you
are not sure how to wire the ceiling fan consult a qualified electrician. For the basic means of
wiring the ceiling fan (model 1 above) use the following procedure(Figure 3)
Blue or black (Neutral)to the terminal marked N
Brown or Red (Live)to the terminal marked L
Green/Yellow or Green (Earth)to the terminal marked
Ensure that earth terminal of the canopy is securely connected to the earth pole of the terminal
block.
Ensure that all electrical connections are tight and that no loose strands are left out of the terminal
block. Cover the terminal block with insulation tape.
FAMATE
CONNECTOR
Warning : If there are only two wires in your existing mains wiring,this means that there is no
Ask a qualified electrician to provide an Earth facility.
The installation must be provided with a double pole switch.
INCOMING MAINS SUPPLY
(GREEN /YELLOW)
N
BLUE
L
BROWN
ASSEMBLY & FITTING INSTRUCTIONS
IMPORTANT
CAUTION
LOCATION
TOOLS AND MATERIALS REQUIRED
UNPACKING
UNSTALLING THE MOUNTING PLATE
INSTALLING THE FAN
CONNECTION TO THE LIGHT CIRCUIT
Earth. Under no circumstance should you wire up this fitting without using an Earth connection.
1