Acuity Controls ECLYPSE A1000 Посібник з монтажу - Сторінка 12
Переглянути онлайн або завантажити pdf Посібник з монтажу для Реле Acuity Controls ECLYPSE A1000. Acuity Controls ECLYPSE A1000 14 сторінок. Asset tracking
Також для Acuity Controls ECLYPSE A1000: Посібник з монтажу (10 сторінок)
Друкувати сторінку
8-0 Additional Information
8-1 Maintenance
Turn off power before any kind of servicing.
Regular Maintenance: Each controller requires minimal maintenance, but it
is important to take note of the following:
•
Clean the outside of the controller by polishing it with a soft dry
cloth.
•
Retighten terminal block connector screws annually to ensure the
wires remain securely attached.
8-2 Disposal
The Waste Electrical and Electronic Equipment (WEEE) Directive sets out
regulations for the recycling and disposal of products. The WEEE2002/96/
EG Directive applies to standalone products, for example, products that can
function entirely on their own and are not a part of another system or piece
of equipment.
For this reason Acuity products are exempt from the WEEE Directive.
Nevertheless, Acuity products are marked with the WEEE symbol ,
indicating devices are not to be thrown away in municipal waste.
Products must be disposed of at the end of their useful life according to
local regulations and the WEEE Directive.
8-3 North American
Emissions Compliance
United States:
Changes or modifications not expressly approved by
Acuity could void the user's authority to operate the
equipment.
•
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential and
commercial installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for
help.
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitybrands.com © 2019 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/07/2019
8-3 North American Emissions
Compliance - cont'd
Canada:
•
This Class (B) digital apparatus meets all the requirements of
the Canadian Interference-Causing Equipment Regulations.
•
Cet appareil numérique de la Classe (B) respecte toutes les
exigences du Règlement sur le matériel brouilleur du Canada.
8-4 Complementary Information
The Power Supply Module (100-240VAC) is designed for type 1 action and
type 1.b action. The EMC immunity test passed using 230 VAC and 0.5
A. The Ball pressure Test temperature was 167°F (75°C) for the Enclosure
and 257°F (125°C) for the Connectors. The SELV must not exceed 42 VDC.
The maximum accessible voltage is 19 VDC. All connecting cables must be
permanently installed with X-type anchors. All cables must have insulation
rated for 176°F (80°C) or higher. These products are classified as integrated
electronic operation control devices. SELV is guaranteed by reinforced
insulation.
For the Power Supply Module (100-240VAC): Risk
of electric shock. Do not open. This product has no
user-serviceable parts inside. When power has been
disconnected, dangerous residual internal voltages may
still be present. Return this unit to Acuity for maintenance
or repair.
12 of 14