Motorola KEM-ML34301 Посібник користувача - Сторінка 2
Переглянути онлайн або завантажити pdf Посібник користувача для Двостороннє радіо Motorola KEM-ML34301. Motorola KEM-ML34301 2 сторінки. Mt series two-way radio
Також для Motorola KEM-ML34301: Специфікація (5 сторінок)
Друкувати сторінку
•
Low battery alert tone or
3. Press
to set the new call tone or
to continue set up.
•
The transmitted talk confirmation tone
To transmit your call tone to other radios set to the same channel and
Interference Eliminator Code as your radio, press
.
Transmitting a Talk Confirmation Tone
You can set your radio to transmit a unique tone when you finish
Note: Setting the call to 0 disables the call tone feature.
transmitting. It is like saying "Roger" or "Over" to let others know you
are finished talking.
Hands-Free Use Without Accessories (
)
1. With the radio on, press
You can use the iVOX feature to transmit hands-free without the need for
On/Off flashes.
any headset accessories. Once iVOX is turned on, the radio detects your
voice and transmits when you speak into the internal microphone.
2. Press
1. Press
until
appears on the display. The current setting
3. Press
On/Off will flash.
Dual Watch Scan
2. Press
or
to select On or Off.
This feature allows you to monitor two channels at the same time.
3. Press
to set or
to continue set up.
1. Press the
2. Press the
Hands-Free Use With Accessories (
)
Watch reception. (if you want to disable the Dual Watch function, set
You can transmit hands-free more reliably with the use of optional
it to 'OFF').
headset accessories. Once VOX is turned on, the radio detects your
3. Press
voice and transmits when you speak.
When the Dual Watch feature is activated, the radio will switch
Many accessories (sold separately) are available for your radio. For
sequentially between the primary and the Dual Watch channels.
more information, visit our Web site at motorolasolutions.com/talkabout
The active channel will display for five (5) seconds after any activity has
or shop.giantintl.com.
ended on the dual channel. You may talk on the Dual Watch channel
1. Turn the radio off and plug the VOX accessory into the accessory port.
during this period.
2. Turn the radio on. VOX shows on the display.
3. Adjust the volume appropriately by rotating
. Lower the volume
before placing the accessory on your head or in your ear.
Emergency Alert Mode
4. To turn off, simply remove accessory.
The Emergency Alert feature can be used to signal members in your
Note: There is a short delay between the time you start talking and when
group of your need for urgent help. MT series radios will operate in an
the radio transmits. There is a short delay before the transmission is
automatic "hands-free" emergency control mode for a total of 30
completed.
seconds after activating the Emergency Alert. MT series radios in your
group will automatically advance the speaker volume to the maximum
Setting the Sensitivity Level When in
Mode
setting and sound a warbling alert tone for 8 seconds. The alert tone is
emitted from your own radio speaker and the receiving radios in your
Adjusting the radio's sensitivity level helps minimize the possibility of
group. After the 8 second alert, any spoken words or incidental sounds at
unintended noises triggering a transmission and helps the radio pick up
your end will be transmitted to the group for 22 seconds. For the 30
soft voices.
second duration of Emergency Alert mode, MT series radio controls and
1. Press
until VOX and the level setting (1 - 3) appear on the
buttons will be locked to maximize reception of the emergency message.
display.
1. Press and hold the Emergency Alert button for 3 seconds.
2. Press
or
to select the sensitivity level.
2. Release the button after the LED Indicator glows red and the alert tone
3. Press
to set or
to continue set up.
begins to sound. There is no need to continue to hold the Emergency
Alert button or use PTT for your message to be transmitted.
3 = High Sensitivity for quiet environments
3. After the alert tone ends you may speak into the microphone. Your
2 = Medium Sensitivity for most environments
voice or incidental sounds will be transmitted. The LED indicator will
1 = Low Sensitivity for noisy environments
continue to glow for the duration of the 22 second period.
4. After 30 seconds your radio speaker will emit a Talk Confirmation
Note: When you connect a headset, the radio is automatically set to the
Tone and the LED Indicator will extinguish. Operation then returns to
last chosen sensitivity level.
normal two-way mode.
Q
Noise Filtering
Note: All Motorola Talkabout EM, MJ, MR, and MT series radios are fully
T
The Q
noise-filtering feature helps to ensure uninterrupted
compatible with the Emergency Alert feature. Radios other than EM, MJ,
T
MR, and MT series can receive the emergency alert signal, but will not
communication with other Motorola radios that have this feature.
respond with adjusted volume settings, locked controls, or a warbling
This feature also filters out unwanted transmissions from other
alert tone. Users of other radio models set to the same channel and
radios. This is useful in places where there is heavy radio traffic,
Interference Eliminator Code will hear a steady tone for 8 seconds
such as amusement parks or ski resorts.
followed by the voice transmission for 22 seconds.
Note: Q
noise filtering is not available when the radio is scanning.
T
Warning: The Emergency Alert feature should only be used in the event
of an actual emergency. Motorola is not responsible if there is no
To turn Q
noise filtering on or off:
T
response to the emergency alert from the receiving group.
1. Press
until
displays. The current setting On/Off will flash.
Built-in Flashlight
2. Press
or
to turn noise filtering On or Off.
Press and hold the flashlight button to turn and keep the light on. The
3. Press
to confirm your selection or
to continue set up.
switch functions as a momentary control for the light.
To transmit to a radio that has Q
noise filtering turned on:
Note: Turn off the flashlight when not in use to conserve battery power.
T
1. Select the same channel and Interference Eliminator Code as
Keypad Lock
the other radio.
To avoid accidentally changing your radio settings:
2. Press
to send a call tone. This allows your voice to pass
1. Press and hold
through the Q
noise filter on the receiving radio.
T
2. When in lock mode, you can turn the radio on and off, adjust the
3. Press
and speak normally.
volume, receive, transmit, send a call tone, and monitor channels. All
Note: If you skip step 2, the beginning of your message may not be
other functions are locked.
heard on the receiving radio. For a 30-second period, starting after
To unlock the radio, press and hold
the last transmission, all transmissions received on the selected
channel and code will pass through the Q
noise filter.
Scanning Channels
T
Use scan to search the 22 channels for transmissions from unknown
VibraCall
Alert
TM
parties, to find someone in your group who has accidentally changed
VibraCall
is a vibrating alert that notifies you that your radio is
TM
channels, or to quickly find unused channels for your own use.
receiving a message. This is useful in noisy environments. When the
There is a priority feature and 2 modes of scanning ( basic and
alert is on, the radio vibrates once every 30 seconds when you receive a
advanced ) to make your search more effective. The basic scan mode
message on the channel and code you set.
uses the channel and code combinations for each of the 22 channels as
1. To turn vibrating alerts on, press
until
is displayed. The
you have set them ( or with the default code value of 1). The "Advanced
current setting will flash.
Scan" mode will scan all channels for any and all codes, detect any
code in use, and use that code value temporarily for that channel.
2. Press
or
to change the setting to On/Off.
Priority is given to the "home channel," that is, the channel (and
Interference Eliminator Code) your radio is set to when you start the scan.
3. Press
to set or
to continue set up.
This means the initial channel (and code setting) is scanned more often
Keypad Tones
than the other 21 channels, and your radio will respond quickly to any
You may enable or disable the speaker key tones. You will hear the key
activity occurring on the home channel as a priority.
tone each time a button is pushed.
To start Scanning:
1. Press
until
appears. The current setting On/Off will flash.
1. Briefly press the
radio will begin to scroll through the channel and code combinations.
2. Press either
or
to turn On or Off.
2. When the radio detects channel activity matching the channel and
3. Press
to confirm or
to continue set up.
code combination, it stops scrolling and you can hear the
Note: When the key tone feature is off, the following are not disabled:
transmission.
•
Transmit timeout alert tone
•
Call tone
Flash Light LED
3. To respond and talk to the person transmitting, press
seconds after the end of the transmission.
4. The radio will resume scrolling through the channels five seconds
Numbers for Channel,
after the end of any received activity.
Call Tone
5. To stop scanning, briefly press the
To start Advanced Scanning:
until the
appears. The current setting
Numbers for Codes
1. Set the Interference Eliminator Code to "zero" or OFF.
2. Briefly press the
or
to turn On or Off.
the radio will begin to scroll through the channels. No Interference
to set or
to quit menu mode.
—Battery Meter
Eliminator Codes will filter what is heard.
—Vibrate
3. When the radio detects channel activity with ANY code (or NO
—Scan
—Channel Power
code), it stops scrolling and you can hear the transmission. Any
Indicator
—Dual Scan
button until the Dual Channel Scan icon
displays.
Interference Eliminator Code that may be in use by that party will be
(see menu Options)
detected and displayed.
or
buttons to select the second channel for Dual
—Call Tone,
—Keypad Lock
Keypad Tone
4. To respond and talk to the person transmitting, press
seconds of the end of the transmission. The radio will transmit using
—Weather Alert
—Talk Confirmation
or the PTT button to confirm the channel selection.
the newly detected Interference Eliminator Code.
Tone (Roger Beep)
—Hands-Free Use
5. The radio will resume scrolling through the channels five seconds
Without
after the end of any received activity.
—Noise Filtering
Accessories
6. To stop scanning, briefly press the
—On/Off for each
Scanning Notes:
—Hands-Free Use
feature
1. If you press
while the radio is scrolling through inactive
With Accessories
channels, the transmission will be on the "home channel". Scanning
will resume five seconds after the end of your transmission. You may
Special Features
press the
key to stop scanning at any time.
2. If the radio stops on an undesired transmission, you may immediately
resume the scan by briefly pressing
3. If the radio repeatedly stops on an undesired transmission, you may
temporarily remove that channel from the scan list by pressing and
holding
or
for three seconds. You may remove more than one
channel in this way.
4. To restore the removed channel(s) to the scan list, turn the radio off
and then back on, or exit and re-enter the scanning mode by
pressing
.
5. You cannot remove the home channel from the scan list.
6. In Advanced Scan, the detected code will only be used for one
transmission. You must note the code, exit scan, and set that
detected code on that channel to permanently use the detected code.
Your radio can tune in to broadcasts by the United States National Oceanic
and Atmospheric Administration (NOAA) Weather Radio and Environment
Canada Weatheradio.
You can listen to a weather channel (see "Weather Channels and
Frequencies" table below) or set your radio to alert you to emergency
weather broadcasts that interrupt routine broadcasts. When you listen to a
weather channel, you cannot use your radio in scan mode or for two-way
communications.
Both NOAA and Environment Canada have transmitters located throughout
the United States and Canada, respectively. These transmitters broadcast
watches, forecasts, and other information 24 hours a day.
Note: NOAA weather radio stations are assigned to cover specific areas and
service may be limited. Please check with your local weather office for
frequency and details, or visit www.weather.gov/nwr in the US or
www.msc.ec.gc.ca/msb/weatheradio in Canada to view the appropriate
transmitter for your area.
The use of the NOAA logo does not provide an endorsement or implied
endorsement by NOAA's National Weather Service, nor does the use of the
Weatheradio logo provide an endorsement or implied endorsement by
Environment Canada.
Turning Weather Channel Reception On and Off
1. To turn weather reception on, press
until
displays.
2. To turn off, press
Setting the Weather Channel
Your radio receives weather frequencies:
1. After turning weather reception on, press
until
is no longer displayed.
channel flashes.
2. Press
or
to select the appropriate channel with good
reception in your area.
3. Press
to save the weather channel setting.
Setting the Weather Alert
Your radio can be set to respond to NOAA Weather Radio emergency
messages. A special alarm tone sounds an alert and turns on the
weather receiver to give you immediate weather and emergency
information.
1. After turning weather reception on, press
2. Press
or
to select On/Off. If you activate Weather Alert and
return to two-way mode,
3. Press
to save the Weather Alert setting.
4. Press
to return to two-way mode.
As with two-way radio reception, weather channel reception depends on
key. The scan
will appear in the display, and the
how close you are to a transmitter and whether you are indoors or
outdoors. Because weather channels are transmitted without codes, they
may contain static or noise. Weather Alert will not function while actively
transmitting or receiving in two-way mode.
Scanning for Weather Channel
within five
The radio can scan for an active NOAA transmission automatically.
1. After turning weather reception on, briefly press the
2. The scan icon
will appear in the display, and the channel will
scroll through the NOAA channels 1-7.
key.
3. When the radio detects channel activity, it stops scanning and you
can hear the transmission.
4. You may resume the scan by briefly pressing
key. The scan
will appear in the display, and
5. To stop scanning, briefly press the
disappear.
Weather Channels and Frequencies
Weather
Frequency
within five
Channel
WX1
162.550 MHz
WX2
162.400 MHz
key.
WX3
162.475 MHz
WX4
162.425 MHz
WX5
162.450 MHz
WX6
162.500 MHz
or
.
Channels and Frequencies
Channel Frequency
Description Channel
1
462.5625 MHz GMRS/FRS
2
462.5875 MHz GMRS/FRS
3
462.6125 MHz GMRS/FRS
4
462.6375 MHz GMRS/FRS
5
462.6625 MHz GMRS/FRS
Weather Receiver
6
462.6875 MHz GMRS/FRS
7
462.7125 MHz GMRS/FRS
8
467.5625 MHz
FRS
9
467.5875 MHz
FRS
10
467.6125 MHz
FRS
11
467.6375 MHz
FRS
and hold for 3 seconds.
or turn the radio off and then back on.
. The current
Patent and Copyright Information
Manufactured, distributed or sold by Giant International Ltd., official
licensee for this product. MOTOROLA, MOTOROLA SOLUTIONS and
the Stylized M Logo are trademarks or registered trademarks of
Motorola Trademark Holdings, LLC and are used under license. All
other trademarks are the property of their respective owners.
©2012 Motorola Solutions, Inc. All rights reserved.
twice. On/Off displays.
will display.
—Channel Power
—Scan
Indicator
—Dual Scan
(see menu Options)
Warranty
—Call Tone,
key.
—Keypad Lock
Keypad Tone
Consumer Two-Way Radio Products and Accessories purchased in
the United States or Canada.
—Weather Alert
—Talk Confirmation
Tone (Roger Beep)
—Hands-Free Use
What Does this Warranty Cover?
Without
—Noise Filtering
Subject to the exclusions contained to the right, Giant International
Accessories
or
.
Ltd. warrants the Motorola branded consumer two-way radios that
—On/Off for each
operate via Family Radio Service or General Mobile Radio Service
—Hands-Free Use
key. The scan icon
will
feature
With Accessories
that it manufactures ("Products"), the Motorola branded or certified
accessories sold for use with these Products that it manufactures
("Accessories") to be free from defects in materials and
workmanship under normal consumer usage for the period(s)
outlined below. This limited warranty is a consumer's exclusive
remedy, and applies as follows to new Motorola branded Products
Weather
Frequency
and Accessories manufactured by Giant International Ltd., and
Channel
purchased by consumers in the United States or Canada, which are
WX7
162.525 MHz
accompanied by this written warranty:
WX8
161.650 MHz
Who is covered?
This warranty extends only to the first consumer purchaser, and is
WX9
161.775 MHz
not transferable.
WX10
161.750 MHz
What will GIANT INTERNATIONAL LTD. do?
GIANT INTERNATIONAL LTD., at its option, will at no charge repair,
WX11
162.000 MHz
replace or refund the purchase price of any Products or
Accessories that does not conform to this warranty. We may use
functionally equivalent reconditioned/ refurbished/ pre-owned or
new Products, Accessories or parts.
Products Covered
Length of Coverage
Frequency
Description
Products and Accessories as
One (1) year from the date of
defined above, unless
purchase by the first consumer
12
467.6625 MHz
FRS
otherwise provided for below.
purchaser of the product unless
otherwise provided for below.
13
467.6875 MHz
FRS
1. Consumer Two-Way Radio
1. Ninety (90) days from the
14
467.7125 MHz
FRS
Accessories.
date of purchase by the first
consumer purchaser of the
15
462.5500 MHz
GMRS
product.
16
462.5750 MHz
GMRS
2. Products and Accessories
2. The balance of the original
that are Repaired or
warranty or for ninety (90)
17
462.6000 MHz
GMRS
Replaced.
days from the date returned
to the consumer, whichever
18
462.6250 MHz
GMRS
is longer.
19
462.6500 MHz
GMRS
20
462.6750 MHz
GMRS
21
462.7000 MHz
GMRS
22
462.7250 MHz
GMRS
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE
DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE REPAIR,
REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS EXPRESS
LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE
CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OF IMPLIED. IN NO EVENT SHALL
MOTOROLA SOLUTIONS, INC. OR GIANT INTERNATIONAL LTD. BE
LIABLE, WHETHER IN CONTRACT OR TORT (INCLUDING
NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE
OF THE PRODUCT OR ACCESSORY, OR FOR ANY INDIRECT,
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY
KIND, OR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS,
LOSS OF INFORMATION OR OTHER FINANCIAL LOSS ARISING OUT
OF OR IN CONNECTION WITH THE ABILITY OR INABILITY TO USE
THE PRODUCTS OR ACCESSORIES TO THE FULL EXTENT THESE
DAMAGES MAY BE DISCLAIMED BY LAW.
Some states and jurisdictions do not allow the limitation or
exclusion of incidental or consequential damages, or limitation on
the length of an implied warranty, so the above limitations or
exclusions may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights that vary from state
to state or from one jurisdiction to another.
Exclusions
Normal Wear and Tear. Periodic maintenance, repair and
replacement of parts due to normal wear and tear are excluded
from coverage.
Batteries. Only batteries whose fully charged capacity falls below
80% of their rated capacity and batteries that leak are covered by
this limited warranty.
Abuse & Misuse. Defects or damage that result from: (a) improper
operation, storage, misuse or abuse, accident or neglect, such as
physical damage (cracks, scratches, etc.) to the surface of the product
resulting from misuse; (b) contact with liquid, water, rain, extreme
humidity, heavy perspiration, when the battery door or accessory port
seals are not closed, sand, dirt or the like, extreme heat, or food; (c)
use of the Products or Accessories for commercial purposes or
subjecting the Product or Accessory to abnormal usage or conditions;
or (d) other acts which are not the fault of Motorola Solutions, Inc. or
Giant International Ltd., are excluded from coverage.
Use of Non-Motorola branded Products and Accessories. Defects
or damage that result from the use of Non-Motorola branded or
certified Products or Accessories or other peripheral equipment
are excluded from coverage.
Unauthorized Service or Modification. Defects or damages
resulting from service, testing, adjustment, installation,
maintenance, alteration, or modification in any way by someone
other than Motorola Solutions, Inc, Giant International Ltd. or its
authorized service centers, are excluded from coverage.
Altered Products. Products or Accessories with (a) serial numbers
or date tags that have been removed, altered or obliterated; (b)
broken seals or that show evidence of tampering; (c) mismatched
board serial numbers; or (d) nonconforming or non-Motorola
branded housings, or parts, are excluded from coverage.
Communication Services. Defects, damages, or the failure of
Products or Accessories due to any communication service or
signal you may subscribe to or use with the Products or
Accessories is excluded from coverage.
How to Obtain Warranty Service or Other Information?
To obtain service or information, please call:
USA and Canada Two-Way Radios
1-800-638-5119
For Accessories, please call the telephone number designated
above for the product with which they are used.
You will receive instructions on how to ship the Products or
Accessories at your expense, to a GIANT INTERNATIONAL LTD.
Authorized Repair Center. To obtain service, you must include: (a) a
copy of your receipt, bill of sale or other comparable proof of
purchase; (b) a written description of the problem; (c) the name of
your service provider, if applicable; (d) the name and location of the
installation facility (if applicable) and, most importantly; (e) your
address and telephone number.
MT Series