Philips 17PF9946/37 Посібник з швидкого використання та підключення - Сторінка 2
Переглянути онлайн або завантажити pdf Посібник з швидкого використання та підключення для ТЕЛЕБАЧЕННЯ Philips 17PF9946/37. Philips 17PF9946/37 4 сторінки. 17” widescreen flattv
Також для Philips 17PF9946/37: Технічні характеристики (2 сторінок), Технічні характеристики (2 сторінок)
Друкувати сторінку
R
C
EMOTE
ONTROL
T
o load the supplied batteries into the remote:
1
Remove the battery compartment door on the back of the
remote.
2
After removing the plastic isolation sheet from the battery,
place the battery (3V) in the remote. Be sure the (+) and (–)
ends of the batteries line up correctly (the inside of the case is
marked).
3
Reattach the battery compartment door.
C
/C
ABLE
ABLE
Y
our Cable TV input into your home may be a single (75 ohm)
cable or use a cable box decoder. In either case the connec-
tion is very simple. Follow the steps below to connect your cable
signal to your new television.
Direct Cable Connections:
This connection will supply Stereo sound to the TV.
1
Connect the open end of the round Cable Company sup-
plied cable to the 75Ω input on the bottom of the TV. Screw
it down finger tight.
Cable Box (w/RF In/Outputs):
This connection will NOT supply Stereo sound to the TV. The sound
from the cable box will be mono.
1
Connect the open end of the round Cable Company sup-
plied cable to the cable signal IN(put) plug on the back of
the Cable Box.
2
Using a separate round coaxial cable, connect one end to the
OUT(put) (TO TV) plug on the back of the Cable Box.
3
Connect the other end of the round coaxial cable to the
75Ω input on the bottom of the television. Screw it down fin-
ger tight.
NOTE: Be sure to set the OUTPUT CHANNEL SWITCH on the
back of the cable box to CH 3 or 4, then tune the cable box on the
TV to the corresponding channel. Once tuned, change channels at
the cable box, not the television.
Cable Box (w/Audio/Video Outputs):
This connection will supply Stereo sound to the TV.
1
Connect the open end of the round Cable Company sup-
plied cable to the cable signal IN(put) plug on the back of
the Cable Box.
2
Using an RCA type Video Cable, connect one end of the
cable to the Video (yellow) (or ANT, your cable box may be
labeled differently) Out jack on the cable box and the other
end to the Video end of the composite adapter included with
the TV.
3
Using an RCA type Audio Left and Right Cable, connect one
end to the left and right Audio Out L & R jacks (red &
white) on the cable box. Connect the other ends to the Audio
end of the composite adapter cable included with the TV.
Connect the adapter into the AV In jack on the bottom of the
TV.
NOTE: Use the AV+ button and the Number 1 button on the TV
remote control to tune to the AV1 channel for the cable box signal.
Once tuned, change channels at the cable box, not the television.
Pressing the AV+ button repeatedly will scroll all the AV Input chan-
nels, including the presently tuned channel.
A
NTENNA
A
combination antenna receives normal broadcast chan-
nels (VHF 2–13 and UHF 14–69). Your connection is
easy because there is only one 75Ω (ohm) antenna plug on
the back of your TV, and that's where the antenna goes.
1
If your antenna has a round cable (75 ohm) on the end,
then you're ready to connect it to the TV.
If your antenna has flat, twin-lead wire (300 ohm), you
first need to attach the antenna wires to the screws on a
300- to 75-ohm adapter.
2
Push the round end of the adapter (or antenna) onto the
75Ω (ohm) plug on the bottom of the TV. If the round end
of the antenna wire is threaded, screw it down finger tight.
H
OOKING
B
ATTERIES
Battery Compartment Door
Direct Cable Connection:
B
TV
OX
Cable Box with RF Inputs and Outputs Connection:
Cable Signal
Cable Box with Audio/Video Outputs Connection:
Video Cable
Antenna Connection:
TV
Outdoor or Indoor Antenna
(Combination VHF/UHF)
The combination antenna
broadcast channels 2-13 (VHF)
U
T
P THE
ELEVISION
(shown from the bottom)
Lithium battery (3V)
Cable signal
coming from
Cable Company
(Round 75Ω
coaxial cable)
IN from the
Cable
Company
Round 75Ω
Coaxial Cable
Cable Signal IN
from the Cable
Company
(Yellow)
receives normal
and 14-69 (UHF).
Twin
Lead Wire
Round 75Ω
Coaxial Cable
from Antenna
2
Remote Control
NOTE: The plastic isolation sheet must be removed
for the remote control to function.
Jack Panel Bottom of TV
Output Channel Switch
Jack Panel Bottom of TV
Jack Panel Back
of Cable Box with A/V Outputs
Audio Cables
L & R (Red, White)
300 to 75-ohm
Adapter
Be sure to point the
remote at the remote
sensor window on the
front of the television
when using the remote
control to operate the
television
Jack Panel Back
of Cable Box
Jack Panel Bottom of TV
Jack Panel
Bottom of TV