Toshiba 22SKV Посібник з монтажу - Сторінка 10

Переглянути онлайн або завантажити pdf Посібник з монтажу для Кондиціонер Toshiba 22SKV. Toshiba 22SKV 12 сторінок.

Друкувати сторінку

Stripping length of the connecting cable

Terminal

block

Connecting

Power cord

cable

Model

Power source

Maximum running current

Plug socket & fuse rating

Power cord

Gas Leak Test

Valve cover

Electric parts

cover

Check places for

the outdoor unit.

Remote Control A-B Selection

• When two indoor units are installed in the same room or adjacent two

rooms, if operating a unit, two units may receive the remote control signal

simultaneously and operate. In this case, the operation can be preserved

by setting either one remote control to B setting. (Both are set to A setting

in factory shipment.)

• The remote control signal is not received when the settings of indoor unit

and remote control are different.

• There is no relation between A setting/B setting and A room/B room when

connecting the piping and cables.

To separate using of remote control for each indoor unit in case of 2 air

conditioners are installed near.

Remote Control B Setup.

1. Press RESET button on the indoor unit to turn the air conditioner ON.

2. Point the remote control at the indoor unit.

3. Push and hold

button on the Remote Control by the tip of the pencil.

CHK

"00" will be shown on the display.

MODE

4. Press

during pushing

CHK

disappear and the air conditioner will turn OFF. The Remote Control B is

memorized.

Note : 1. Repeat above step to reset Remote Control to be A.

2. Remote Control A have not "A" display.

3. Default setting of Remote Control from factory is A.

1110651154-EN.indd 8

L N

1 2 3

Earth line

Connecting

Power cord

cable

RAS-18SKV(R)

RAS-22SKV(R)

220 – 240 V Single phase, 50Hz

220 – 230 V Single phase, 60Hz

12A

13.5A

16A

H07RN-F or 60245 IEC66 (1.5 mm

or more)

OTHERS

Check places for

the indoor unit.

• Check the ﬂ are nut connections

for the gas leak with a gas leak

detector or soap water.

. "B" will show on the display and "00" will

CAUTION

• Wrong wiring connection may cause some electrical parts burn out.

• Be sure to comply with local rule on running the wire from indoor unit

to outdoor unit (size of wire and wiring method, etc.).

• Every wire must be connected ﬁ rmly.

• If incorrect or incomplete wiring is carried out, it will cause an ignition

or smoke.

• Prepare the power supply for exclusive use with the air conditioner.

• This product can be connected to the mains.

Connection to ﬁ xed wiring: A switch which disconnects all poles and

has a contact separation of at least 3 mm must be incorporated in the

ﬁ xed wiring.

NOTE

: Connecting cable

• Wire type : H07RN-F or 60245 IEC66 (1.0 mm

"B" Display

"00" Display

PRESET

Test Operation

To switch the TEST RUN (COOL) mode, press RESET button for 10 seconds.

(The beeper will make a short beep.)

Hi POWER FILTER

RESET button

Auto Restart Setting

This product is designed so that, after a power failure, it can restart

automatically in the same operating mode as before the power failure.

Information

The product was shipped with Auto Restart function in the off position.

Turn it on as required.

How to set the Auto Restart

1. Press and hold the RESET button on the indoor unit for 3 seconds to set

the operation. (3 beep sound and OPERATION lamp blink 5 time/sec for

5 seconds)

2. Press and hold the RESET button on the indoor unit for 3 seconds to

cancel the operation. (3 beep sound but OPERATION lamp does not

blink)

• In case of ON timer or OFF timer are set, AUTO RESTART

OPERATION does not activate.

or more)

FAN

PAP

TIMER OPERATION

RESET

2/15/10 9:39:42 AM