Toshiba 15LZU28X Посібник користувача

Переглянути онлайн або завантажити pdf Посібник користувача для ТЕЛЕБАЧЕННЯ Toshiba 15LZU28X. Toshiba 15LZU28X 2 сторінки. Toshiba color television owners manual 15lzj28, 15lzr17, 15lzr28, 15lzu28x

O
M
WNER'S
ANUAL
Color Television
Owner's Record
15LZR 17/28
You will find the model number and serial number on
the back of the TV. Record these numbers in the spaces
15LZJ 28
provided below. Refer to them whenever you call upon
your TOSHIBA dealer regarding this product.
Model number:
15LZU 28X
Serial number:
Printed in Indonesia
©TOSHIBA CORPORATION, 2006
All Rights Reserved
GETTING STARTED
• The illustrations in this manual are of 15 LZJ28 model, if otherwise , it will be stated.
Connect the antenna to
at the
Push the q (Power switch) on the
front of TV until it clicks to turn on
rear of the TV.
the power.
Adjust to the best
Refer to page section J for details on power
possible reception
UHF
on and off.
VHF
Outdoor
antenna
(optional)
Preset the channels automatically
Mixer
(ASM function).
Use remote control for this operation. The
75-ohm coaxial cable
or
Rod antenna
buttons on the TV with similar name may
(supplied*)
also be used.
* 15LZJ28 only
1
Select the starting position for channel
Connect the power cord to an
to be preset. Press the Number buttons
electrical outlet
~110V-240V, 50/60Hz
(-/--, 0~9) or CH s/t.
(15LZJ28)
~220V-240V, 50Hz
(15LZR17 / 15LZR28)
1
~220V, 50Hz
(15LZU28X)
Notes
• Do not connect the power cord until all
2
Set the correct broadcast system for
your equipments have been connected.
your region. Press MENU and then
• The antenna cables should not be
; -/+ to highlight the "
SET UP" icon.
bundled with the power cord and the like.
Insert the batteries into the remote
control.
Operating range
Confirm "COLOR" is set to "AUTO" and
"SOUND" is set to proper system. (Refer
5m
to the table on page section G.) If not,
press CH s/t to select "COLOR" or
Remote sensor
Requires two R03
"SOUND" and press ; -/+ to set each
(AAA) batteries
proper system.
3
Press MENU and then ; -/+ to highlight
• If the remote control does not operate
the "
TUNING" icon. Select "ASM",
correctly, if the operating range becomes
then press ; + to start the search. When
reduced, replace both batteries with
new ones.
the TV screen returns to the start position,
• When the remote control will not be used
the procedure is completed.
for a long period of time or when the
batteries are worn out, remove the
batteries to prevent leakage.
CH
• Do not drop, dampen or disassemble the
CH
remote control.
Cautions
• Do not dispose batteries into fire. Dispose
Press ; -/+ to adjust the sound
batteries into the designated disposal
areas according to the local regulations.
volume.
• Do not mix battery types or combine used
batteries with new ones.
En01_01[15LZR17/28/JU28X]-8
1
SAFETY INSTRUCTIONS AND MAINTENANCE
For safety
1)
If and when anything abnormal occurs, unplug the power cord from the outlet immediately.
Make sure that the smoke has stopped, then contact for a service.
Continual usage of TV in such condition may cause a fire or an electric shock.
2)
Do not cut, break, heat, modify, twist, bunch up or bent the cord or apply excessive force or
tension to it, as this may cause damage, fire or electric shock. Contact a service technician if
the power cord is damaged.
3)
Do not pull on the power cord when removing the plug from the wall outlet. Always hold
the plug firmly when removing it. If the power cord is yanked, the cord may become
damaged and fire or electric shock may occur.
4)
Do not repair, modify or disassemble the TV by yourself. Let qualified technicians check and
adjust your TV. To avoid electrical shock or fire, never modify the TV.
5)
Do not place hot objects or naked flame sources, such as lighted candles or nightlights, on
or close to the TV. High temperature can melt plastic and lead to fires.
6)
The TV shall not be exposed to dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed on the TV. This may cause a fire or electric shock.
7)
Do not let metallic materials and/or combustibles get in the TV. These items may cause a
fire or an electric shock. Be especially observant when children are present.
8)
Do not stand or climb on the TV. The TV is dangerous if it is broken or if it has fallen down.
Be especially observant when children are present.
9)
When the TV will not be used for a long period of time, unplug the power plug from the outlet
for safety.
The main power plug or an appliance coupler is used as a disconnecting device and therefore
should be remain readily operable.
10) During lightning storm, do not touch any part of the TV, including the power cord and the
antenna lead-in-wire. You may suffer an electric shock.
2)
3)
4)
7)
8)
9)
VX1A00014100
EXTERNAL EQUIPMENT CONNECTIONS
• You can connect video equipments such as a VTR and video camera to this TV and enjoy the
high quality picture. The front A/V terminal a (1) is convenient when hooking up video camera
or game equipment.
• The following describes how to use and connect the TV with other AV equipment. Refer to the
owner's manual of the equipment to be connected as well.
• Connection cables are not supplied.
Caution: Do not plug in any power cords until you have finished connecting all equipment.
For 15LZJ28 / 15LZR28 / 15LZU28X models
Front
Back
Y
(1)
(MONITOR)
VIDEO
VIDEO
W
L/MONO
L/MONO
Y
W
R
+
R
AUDIO
AUDIO
or
R
Y
W
R
To video
To audio
Y
W
R
output
outputs
To
video/
audio
outputs
PLAY BACK
VTR etc.
Video camera
For 15LZR17 model
Front
Back
B
Y
(1)
(MONITOR)
VIDEO
VIDEO
Y
W
W
AUDIO
+
or
To
video/
Y
W
To audio
audio
To video
Y
W
output
output
outputs
PLAY BACK
VTR etc.
Video camera
>
Notes
• The
MONITOR terminals output the TV
• Connect the equipment to either front or back
program or video (A ) signals being
a (1) terminal. Audio and video interference
displayed on the screen. You can record a TV
may occur if both terminals are connected.
program or video signals by connecting a VTR
• Do not connect one VTR to the output and
B
from the output terminals (
>
MONITOR) to
input terminals on the TV simultaneously, it
the input terminals of the VTR. However,
may cause interference.
except for personal use, you are not allowed
• For 15LZJ28 / 15LZR28 / 15LZU28X models,
to use video or sound you have recorded
when connecting the audio signal to a
monaural equipment, connect AUDIO L or R
without consent of the owner of copyright
terminal of the TV to the AUDIO terminal of
according to copyright law.
the equipment.
• For 15LZR17 model, when connecting the
audio signal to a stereo equipment, connect
them to the L/MONO terminal of the
equipment. Otherwise, connect the audio
signal to either L or R terminal.
SAFETY INSTRUCTIONS AND MAINTENANCE (continued)
Notes on installation and on use
11) Place the TV on a horizontal, stable surface. Avoid location subject to vibration. Do not place
the TV on its side or back. Otherwise, the TV may drop or fall off which may cause injury or
damage.
12) Do not block the ventilation holes. Place the TV at least 10 cm away from the walls for good air
circulation. The inside of this TV will overheat if the ventilation holes are sealed, which may
result in a fire.
13) Take measures to prevent the TV from falling over. If not, the TV may lean or fall over and
cause an injury. When moving, watch out for the ties.
14) Avoid placing the TV in direct sunshine, near a heating source or places with a high temperature,
such as in a closed car. A fire may result when the inside temperature increases.
15) Also avoid the placing the TV on dusty or damp places. This may cause a fire or electric shock.
16) Set up the outdoor antenna away from high ways, power lines and neon signs. If the antenna
falls down or drops, it may cause injury or electric shock accidents.
The antenna should be checked and replaced periodically.
17) Do not jolt the TV, resulting in the TV falling over, dropping or causing an injury.
18) Keep magnets, electric clocks, speakers, etc. away from the TV.
19) Do not spray volatile compounds such as insecticide on the cabinet. This may cause a
discoloration or damage of the cabinet.
Notes on cleaning
20) Before cleaning, unplug the power plug.
Clean the cabinet with a soft and dry cloth.
Do not use benzine, thinner, etc. to clean the TV.
21) Sometimes disconnect the power plug from the outlet and check it.
If dust has collected on the power plug connectors, clean off the dust.
5), 6)
12)
16)
20)
10)
TROUBLESHOOTING
Before calling service personnel, please check the following chart for a possible cause to the
trouble you are experiencing.
Symptom
• Be sure the power cord is plugged in.
Power is not turned on.
• The headphones may be plugged in.
No sound.
• The contrast, color and tint may need to be adjusted.
Poor color/tint.
• If you change the direction of the TV while the TV is on, the picture
: Signal flow
Y
: yellow (Video)
may suffer from color shading. If so, turn off the TV and allow
Y
: white (Audio L/MONO)
W
about 30 minutes to cool, then turn on the TV again. The picture
: red (Audio R)
W
R
may be improved.
R
• The broadcast signal may be jammed by other electrical sources
Spots appear on the
R
screen.
such as cars, motorcycles, electric trains, high tension lines, neon
signs, hair dryers.
R
W
Y
• The broadcast signal may be jammed by other TV receivers,
Lines appear on the
To audio
To video
screen.
personal computers, and TV games, as well as interference from
inputs
input
radio stations.
REC
Double or triple images. • Interference may be due to broadcast waves reflected from
VTR (type without built-in tuner)
mountains or buildings.
• Check if the direction of the antenna has changed due to strong wind.
• The antenna lead may be broken or disconnected.
Snowy picture.
• Check if the direction of the antenna has changed.
: Signal flow
• The batteries in the remote control may be exhausted.
: yellow (Video)
Remote control does
Y
Y
W
: white (Audio)
• The batteries may be improperly installed.
not work.
W
• Check that there is no obstruction between the remote control and
AUDIO
the remote (infrared) sensor.
• Check that a strong light is shining on the remote (infrared) sensor.
• Check that the main power is not turned off.
W
Y
To audio
To video
input
input
The following phenomena are not malfunctions
REC
• The clicking is a creaking sound produced when the cabinet
The cabinet clicks.
VTR (type without built-in tuner)
expands or contracts due to changes in the temperature. This will
not affect the picture or sound.
• If the brightness is set too high, such unevenness in color may
Unevenness in color
sometimes develops
occur depending upon the nature of the picture. The proper color
in part of the screen.
can be restored by reducing the contrast.
21/6/06, 2:59 PM
SPECIFICATIONS
MODEL
Rated voltage
Power consumption
(at ~ 220 V, 50 Hz)
Dimensions
(Width x Depth x Height)
Mass
Picture tube
Television Channel
system
coverage PAL
(Antenna
input)
Special RF Color system
signal
Color system
Sound output
Speaker
Terminal
14)
13)
Not lean
and
protrude
Accessories
Sturdy tie
21)
Design and specifications are subject to change without notice.
Help to recycle, this product indicates material names on main plastic parts.
OTHER INFORMATIONS
Exemptions
9 Toshiba is not liable for any damage caused by natural disaster (such as thunder, earthquake),
fire, acts by third parties, accidents, misuse, or uses in other improper conditions.
Solution
9 Toshiba is not liable for incidental damages (such as profit loss or interruption in business,
modification or erasure of record data, etc.) caused by use or inability to use of product.
9 Toshiba is not liable for any damage caused by neglect of the instructions described in the
owner's manual.
9 Toshiba is not liable for any damage caused by misuse or malfunction through simultaneous
use of this product and the connected equipment.
Broadcast Transmission Systems in Each Country or Region
Area
Bahrain, Kuwait, Israel, Oman, Qatar, United Arab
Emirates, Yemen, and other middle Eastern countries.
Indonesia, Malaysia, Singapore, Thailand, and other
Southeast Asian Countries.
China
Asia
M. E.
China Hong Kong
Iraq, Islamic Republic of Iran, Lebanon, Saudi Arabia
Russian Federation
Myanmar
Oceania
Australia, New Zealand
Africa
Republic of South Africa
Argentina, Paraguay, Uruguay
South
Brazil
America
Chile, Colombia
Notes
• PAL, SECAM and NTSC3.58 are different color signal broadcast transmission systems
applicable to different country or region. NTSC4.43 (MHz) are used in some VTRs to playback
NTSC recorded video tapes through PAL television equipment.
• Refer to the Specifications table to find the receivable television systems for this TV.
15LZR17 / 15LZR28 / 15LZJ28 / 15LZU28X
15LZJ28:
~ 110 V–240 V, 50/60Hz
15LZR17 / 15LZR28:
~ 220 V–240 V, 50Hz
15LZU28X:
~ 220 V, 50Hz
67W
457.5(W) x 393.0(D) x 352.5(H) mm
12.1 kg
Type 15 Flat square picture tube
(393.4mm) Overall picture tube measured diagonally
(355.6mm) Viewable picture tube measured diagonally
90° deflection
System
Channel VHF
UHF
CATV
B/G CCIR
2 – 12 21 – 69 X ~ Z+2, S1 ~ S41
PAL
I
UK
21 – 69 —
PAL
D/K CHINA
1 – 12 13 – 57 Z–1 ~ Z–38
SECAM
B/G CCIR
2 – 12 21 – 69 X ~ Z+2, S1 ~ S41
SECAM
D/K OIRT
1 – 12 21 – 69 X1 ~ X19
NTSC
M
US
2 – 13 14 – 69 A–6 ~ A–1, A ~ W, AA ~ ZZ, AAA, BBB
NTSC
M
JAPAN
1 – 12 13 – 62 M1 ~ M10, S1 ~ S41
Sound system
NTSC4.43
5.5/6.0/6.5 MHz
PAL 60Hz
5.5/6.0/6.5 MHz
PAL/SECAM/NTSC4.43/NTSC3.58
2.5 W X 2
4 X 11cm (2)
For 15LZR17
Input [a(1), front and back]: Video, Audio (monaural)
Output [
>
(MONITOR)]:
Video, Audio (monaural)
For 15LZJ28 / 15LZR28 / 15LZU28X
Input [a(1), front and back]: Video, Audio L, Audio R
Output [
>
(MONITOR)]:
Video, Audio L, Audio R
Headphone output:
Ø3.5 mm (mini jack)
• Remote control
(1)
• Rod antenna
(1)*
• Batteries (R03, AAA) (2)
* 15LZJ28 only
• This Owner's Manual
System
Country or Region
Color
Sound
PAL
B/G
PAL
D/K
PAL
I
SECAM
B/G
SECAM
D/K
NTSC
M
PAL
B/G
PAL
I
PAL
N
PAL
M
NTSC
M