Epson PowerLite Cinema 500 Посібник - Сторінка 9

Переглянути онлайн або завантажити pdf Посібник для Програмне забезпечення Epson PowerLite Cinema 500. Epson PowerLite Cinema 500 13 сторінок. Release of emp ns connection for windows & mac upgrade from v2.50 to v2.51
Також для Epson PowerLite Cinema 500: Посібник користувача (42 сторінок), Посібник з експлуатації (36 сторінок), Брошура (2 сторінок), Посібник з експлуатації (47 сторінок), Перелік деталей (1 сторінок), Посібник користувача (1 сторінок), Бюлетень підтримки продукту (25 сторінок), Бюлетень підтримки продукту (22 сторінок), Бюлетень підтримки продукту (28 сторінок), Бюлетень підтримки продукту (41 сторінок), Бюлетень підтримки продукту (15 сторінок), Бюлетень підтримки продукту (22 сторінок)

Друкувати сторінку

Replacing the Lamp

The projection lamp lasts for up to 3000 hours (in low

brightness mode) or 1700 hours (in high brightness mode). You

can use the Info menu to check how long it's been in use. It's

time to replace the lamp when:

❏ The projected image gets darker or starts to deteriorate.

❏ The projector's lamp light is red.

❏ The message

Replace the lamp

you start projecting.

Note: Lamp life results will vary depending on the selected mode,

environmental conditions, and usage.

Contact your dealer or call Epson at (800) 873-7766 in the

United States for a replacement lamp. Request part number

. In Canada, call (800) 463-7766 for dealer

V13H010L28

referral.

Warning: Let the lamp cool fully before replacing it. In the unlikely

event that the lamp has broken, small glass fragments may be

present and should be removed carefully to avoid injury.

The lamp component contains mercury. Please consult your state

and local regulations regarding proper disposal or recycling, and do

not place in the trash.

Caution: Never touch the lamp with your bare hands; the invisible

residue left by the oil on your hands may shorten the lamp life. Use

a cloth or glove to handle the new lamp.

Follow these steps to replace the lamp:

1. Turn off the projector and wait for the P power light to stop

flashing, then unplug the power cord.

2. If the projector has been on, let it cool for about an hour.

3. Loosen the two screws securing the lamp cover (they don't

come all the way out), and then remove the cover.

appears on the screen when

Epson PowerLite Cinema 500 Projector

4. Loosen the two screws securing the lamp.

5. Grasp the lamp as shown and pull it straight out.

6. Fully insert the new lamp and tighten its screws.

Caution: Don't touch the glass portion of the lamp assembly.

Touching the glass could result in premature lamp failure.

7. Replace the cover and tighten its screws. (The projector

won't work if the lamp cover is open or loose.)

8. Reset the lamp usage timer, as described in the next section.

Resetting the Lamp Timer

After installing a new lamp, you need to reset the timer so the

projector can keep track of how many hours it has been used.

1. Press the

button on the projector or remote control.

2. Use the menu navigation buttons to open the

then select

Lamp-Hours Reset

3. When you see a confirmation prompt, highlight

press the

Select

4. When you're finished, press the

The lamp usage timer doesn't register until you've used the

lamp for at least 10 hours.

2/04

Epson PowerLite Cinema 500 Projector - 9

Reset

button.

button to exit.

menu,

and

Yes