Philips 3 CD CHANGER WITH DOLBY PRO LOGIC PROCESSOR FWP88C Посібник - Сторінка 18
Переглянути онлайн або завантажити pdf Посібник для Стереосистема Philips 3 CD CHANGER WITH DOLBY PRO LOGIC PROCESSOR FWP88C. Philips 3 CD CHANGER WITH DOLBY PRO LOGIC PROCESSOR FWP88C 31 сторінка. 3 cd changer with dolby® pro logic processor, five loudspeakers, 320 watts total power
Також для Philips 3 CD CHANGER WITH DOLBY PRO LOGIC PROCESSOR FWP88C: Посібник користувача (31 сторінок), Технічні характеристики (2 сторінок)
Друкувати сторінку
All manuals and user guides at all-guides.com
CD
Playing a CD
1 Press PLAYÉ Å to start playback.
™ The disc tray, track number and
elapsed playing time of the current
track appear on the display.
• To interrupt playback, press
PAUSEÉ Å .
™ The playing time flashes.
• To resume playback, press PLAYÉ Å
again.
2 To stop playback, press Ç.
Notes:
– All the available discs will play once,
then stop.
– When the CD has stopped playing, the
system will switch to standby mode
after 30 minutes if no button is pressed.
18
pg 01-31/P88/22-Eng
18
Selecting a desired track during
Disc Change
playback
You can change the outer two discs while
• Press í or ë (or Digit 0-9 on the
the third inner disc is stopped or is playing.
remote control) until the desired track
1 Press DISC CHANGE.
appears on the display.
™ The CD carousel tray slides out.
™ The selected track number and
2 Replace the discs in the left and right
disc trays.
• If you press í once it will skip to the
• If you wish to change the inner disc
during playback, press DISC CHANGE
beginning of the current track and play
again.
the track again.
™ "DISC CHANGE" will be displayed.
Note:
™ The CD will stop playing.
– Pressing í during shuffling can only skip
™ The CD carousel tray will close to
to the beginning of the current track.
retrieve the inner CD and then open
again with the inner CD accessible.
Searching for a particular
3 Press OPEN•CLOSE to close the CD
passage during playback
carousel tray.
• Press and hold à or á until the
Selecting a desired track
desired passage is located.
™ The volume will be reduced.
Selecting a desired track when
• Play returns to normal when à or á
playback is stopped
is released.
1 Press í or ë (or Digit 0-9 on the
remote control) until the desired track
appears on the display.
2 Press PLAYÉ Å to start playback.
™ The selected track number and
elapsed playing time appear on the
display.
Programming Tracks
Programming tracks of a loaded CD is
possible when playback is stopped. The
display will indicate the total tracks stored
in the program. Up to 40 tracks can be
stored in the memory in any order. When
elapsed playing time appear on the
40 tracks are stored and you attempt to
display.
store another track, the display will show
"PROGRAM FULL".
1 Load the desired discs in the disc trays.
2 Press PROG to start programming.
™ The
™ It will cancel any previously selected
repeat mode.
3 Press the CD (CD 1•2•3) or DISC 1/2/3
button to select the disc.
4 Press í or ë (or Digit 0-9 on the
remote control) to select the desired
track.
5 Press PROG to store the track.
• Repeat steps 3 to 5 to store other discs
and tracks.
6 Press Ç once to end programming.
™ The total number of tracks
programmed and total playing time
appear on the display.
Notes:
– If the total playing time is more than
" 99:59 " or if one of the programmed
tracks has a number greater than 30,
then " --:-- " appears on the display
instead of the total playing time.
3/6/00, 1:26 PM
starts flashing.
PROGRAM
3139 116 19721