Toshiba TDP-D2-US Посібник користувача - Сторінка 11
Переглянути онлайн або завантажити pdf Посібник користувача для Проектор Toshiba TDP-D2-US. Toshiba TDP-D2-US 20 сторінок. Toshiba tdp-d2-us: specifications
Також для Toshiba TDP-D2-US: Технічні характеристики (2 сторінок), Технічні характеристики (1 сторінок)
Turning the power on and off (Continued)
Notes
• The start-up screen will disappear after a moment. You can dismiss the start-up screen
before this by performing any operation. You can also configure the start-up screen not to
appear via the Display setting menu
• The first time you use the projector after purchase, after the start-up screen disappears,
the Language menu is displayed
p.21
I Turning the power off
1
Press the ON/STANDBY button.
A message appears on the screen, confirming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)
2
Press the ON/STANDBY button again.
The screen turns off, but the internal cooling fan continues to operate for a short while.
Then, the projector goes into standby mode.
When cooling lamp
During internal cooling
FAN
TEMP LAMP
ON
FAN
(Green)
(Green) (Orange)
(Green)
Flashing
A
B
During cooling, the LAMP indicator flashes. In this state, the power cannot be
A
turned back on. In addition, unplugging the power cord or turning off the main
power switch in this state will shorten the life of the lamp.
After the LAMP indicator goes off, the cooling fan continues to operate for a
B
short while, in order to expel excess internal heat. If you are in a hurry, there is
no problem with unplugging the power cord or turning off the main power switch
in this state.
In standby mode
C
Note
• The projector consumes about 6W of power in standby. We recommend that you unplug
the power cord or turn off the main power switch if you will not be using the projector for
an extended period.
PRECAUTIONS
• Before unplugging the power cord or turning off the main power switch, make sure that
the LAMP indicator is off. Unplugging the power cord or turning off the main power
switch and cutting off the power while the projector is running or being cooled will
shorten the life of the lamp. However, please unplug the power cord if the projector
locks up or acts abnormally.
• If the power cord is unplugged before cooling is complete, give the lamp time (about 10
minutes) to cool before plugging it back in. If the lamp overheats it may fail to light, and
its lifetime will be shortened.
.
p.29
.
After cooling complete
TEMP LAMP
ON
FAN
TEMP LAMP
ON
(Off)
(Orange)
(Off)
(Off)
(Orange)
C
20
Basic operations
1
Turn on the power.
Turn on the power, following the instructions in "Turning on the power"
2
Select language (When using for first time).
When the projector is used for the first time after purchase, a message is displayed on
the screen, and the language menu appears. The default language is English.
(If the screen focus is not on the menu, adjust according to step
q Use the
buttons to select the desired
language, and press the
A message displays the selected language.
w Press the
button to erase the message.
Notes
• After the first time the projector is turned on, the Language menu does not appear
upon startup. However, from the Reset menu
Language menu the next time the projector is turned on.
• The language can also be set via the Display setting menu
• This owner's manual assumes that English has been selected.
3
Place connected device(s) in operating status.
Turn on and boot up connected computers and other devices.
Select "Cancel" or install driver contained in the supplied CD-ROM, when the dialog
box of the Add New Hardware Wizard screen appears on the computer when
connecting a computer. (The supplied CD-ROM contains a driver information file
named TOSHIBA_TDP.inf. Click the Browse button of the dialog box to find and
designate this file.)
4
Select input.
q Press the INPUT button.
A list of inputs appears on the screen.
w Use the
buttons to select the desired
input, and press the
button.
The picture for the selected input is projected.
p.19
.)
6
................
English
English
..............
button.
Français
French
..............
Deutsch
German
................
Italiano
Italian
...............
Español
Spanish
..........
Português
Portuguese
...................
Japanese
.......
Chinese (simplified)
.......
Chinese (traditional)
...................
Korean
select "Reset all" to display the
p.29
.
p.29
Remote
Control panel
Control
ON
LAMP
TEMP
FAN
ON/STANDBY
INPUT
MENU
RESIZE OFF
VOL.
-
VOL.
+
VOL.-
AUTO KEYSTONE
AUTO SET
Computer
Y/P
/P
B
R
Video
S-video
21
.
RESIZE INPUT
INPUT
MENU
VOL.+